Bedienungsanleitung Futaba T-16IZ (Seite 191 von 228) (Englisch)

747917

191

Zoom out

Zoom in

Vorherige Seite

1/228

Nächste Seite

191

→ GO to TABLE OF CONTENTS

GovernorBasicGovernorBasic

(6) Stick sw.: Stick switch

The governor can be activated by throttle stick position.

[Setting method] Touch the "Stick SW" button to enter the setting mode.

Operate the throttle stick to the position where you want to turn Governor

ON. Touch the “Stick SW” button again. “Sure?” Is displayed. If you touch

the [Yes] button, the ON position is memorized. This stick switch function is

always enabled when the next "ON / OFF sw" is "INH" or the "Governor ON /

OFF switch is not set by S.BUS setting.

Whengovernoristurnedonando󰮏bytransmitterthrottlestick

The data is set so that the governor can be

turned on and off with the transmitter throttle

stick position. The following describes this op-

eration.

• Throttle stick over set point and more than 60%

of set rotation speed.

*This is the setting value of "Gov. On. Revo: Gov-

ernor ON revolution setting".

• Throttle stick held at the set point or more Re-

mains.

• Throttle stick position is below the set point se-

lected.

OFF

When idle up

• When the throttle curve is set at idle up, and when the throttle output is over the set

value (initial value: 30%), the governor will always and remain ON even if the stick is

lowered to the bottom.

(OFF at slow side)

Set point or less

100%

(Governor operating point)

Set speed

The stick is at, or be-

yond the set point and

is 60% of the rotation

speed value of the gov-

ernor.

When you activate the switch, the direction setting of the switch is displayed.

Select the switch ON / OFF direction (Normal / Reverse).

Whenturningon/o󰮏governorwithswitch

Select the ON / OFF switch channel with "GOV sw channel" on "SBUS BASIC"

menu.

Setting the switch to the ON position turns on, or enables the

governor. The following describes this operation.

• Switch set to on position and engine running at 60% or more

of set speed ON

• Throttle stick set to maximum slow position ON

• Switch set to off position

OFF

(7) ON/OFF sw.: Governor on/o switch

This parameter allows the user to turn the governor on or off via a switch

on the transmitter. Choose INH if you do not want to use it.

Governor can be turned

on and off by a switch.

When Battery Fail Safe is enabled, items for setting the throttle servo posi-

tion are displayed. The setting method is the same as "Stick sw", so please

refer to this section of the manual for information on setting this function.

(8) BAT F/S: Battery fail safe

When the receiver battery voltage becomes equal to or less than "BFS.

Volt" set in the "Governor Expert" menu, the battery fail safe function is ac-

tivated, the governor function is turned OFF, and the throttle servo moves

to the set position.

If the battery voltage is lower than the set voltage of the "Battery F/

S" for about 3 seconds, the Gx (gyro) LED of the CGY solid red light.

When "Battery F/S" is set to "ACT" in "GOV BASIC", the servo is ﬁxed

to the throttle position set by "Battery F/S". When the throttle stick is

set to the slowest position, the "Battery F/S" function is temporarily

canceled. However, after 30 seconds, the "Battery F/S" function is

activated again and the servo is locked. When the "Battery F/S" oper-

ates, quickly landing and stopping the helicopter, please charge the

battery.

WARNING

When using the CGY for the ﬁrst time, or when making changes in

the throw of a servo and its linkage, always perform the limit setting

operation.

WARNING

When using the CGY for the ﬁrst time, or when making changes in

the throw of a servo and its linkage, always perform the limit setting

operation.

(9) Lim. set: Servo limit point setting

Servo limit point setting deﬁnes the overall travel range for the throttle ser-

vo. It is fundamental for governor operation and must be set prior to other

functions. Servo limits must also be reset when the throttle linkage or trim

are changed.

How to set the servo limit point:

Touch the “Lim.Set Id” button to enter the setting mode.

Set the transmitter’s

throttle stick to the idle position.

Touch the “Lim.Set Id” button again.

The

limit of idle will be saved to the CGY.

The cursor will move to "Lim. Set Hi".

Set the stick to the full high position.

Touch the “Lim.Set Hi” button again.

The limit of high will be saved to the CGY.

If the setting data is not normal

(servo operation amount is 50% or less), "Err" is displayed. In this case,

check the transmitter setting and repeat this procedure once again.

(10) Limit Test: Check the set limit point

Check the set limit point. Press "Idle" or "High" to move the servo to each

limit point. Press “End” to end the test.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T-16IZ Seite 191

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info