Bedienungsanleitung Futaba T-16IZ (Seite 198 von 228) (Englisch)

747917

198

Zoom out

Zoom in

Vorherige Seite

1/228

Nächste Seite

198

→ GO to TABLE OF CONTENTS

SwashDetailSwashDetail

The swash detail setting is used to keep the swash plate level at high and low collective pitch to cyclic interactions and cyclic

pitch to collective pitch interactions.

Swash Detail

screen from the

EXPERT MENU 3D

screen.

(1) PIT AIL: collective pitch aileron mixing rate

Going from MID to HIGH and MID to LOW collective pitch check that the

swash plate is traveling ﬂat throughout the entire range.

[Setting method] Operate the transmitter stick in the direction you want to

set. Touch the button lit in green to enter the setting mode and adjust the

mixing rate. Do the same for the other side.

Settingranges:30~150%Initialvalue:100%

(2) PIT ELE: collective pitch elevator mixing rate

Going from MID to HIGH and MID to LOW collective pitch check that the

swash plate is traveling ﬂat throughout the entire range.

[Setting method] Operate the transmitter stick in the direction you want to

set. Touch the button lit in green to enter the setting mode and adjust the

mixing rate. Do the same for the other side.

Settingranges:30~150%Initialvalue:100%

(3) PIT ELE2: collective pitch 2nd elevator mixing rate

This parameter adjusts the pitch to 2nd elevator mixing rate. The rates can

both be adjusted individually for both full high and low collective positions.

Note: This setting is only available if the H4-xx swash mode has been

selected.

Settingranges:30~150%Initialvalue:100%

(4)

AIL PIT: aileron collective pitch mixing rate

At the middle collective pitch, check that during right to left and left to right

aileron action the swash plate is staying level on both the elevator and col-

lective pitch axis. If the swash plate is rising or falling with aileron inputs.

[Setting method] Operate the transmitter stick in the direction you want to

set. Touch the button lit in green to enter the setting mode and adjust the

mixing rate. Do the same for the other side.

Settingranges:30~150%Initialvalue:100%

(5) AIL ELE: aileron elevator mixing rate

This parameter adjusts the aileron to elevator mixing rate. The rate can be

adjusted for left and right directions individually. Note: This setting is only

available if the H4-45 swash mode has been selected.

Settingranges:30~150%Initialvalue:100%

(6) AIL ELE2: aileron 2nd elevator mixing rate

This parameter adjusts the aileron to 2nd elevator mixing rate. The rate

can be adjusted for left and right directions individually. Note: This setting

is only available if the H4-45 swash mode has been selected.

Settingranges:30~150%Initialvalue:100%

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T-16IZ Seite 198

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info