Bedienungsanleitung Futaba T-18MZ-WC (Seite 36 von 178) (Englisch)

747919

Zoom out

Zoom in

Vorherige Seite

1/178

Nächste Seite

＜

Basic Operation

＞

+RZWRWXUQ212))WKH

SRZHURIWKHWUDQVPLWWHU

Windows

CE is installed as a built-in operating

system in the T18MZ-WC transmitter. Compared to

the conventional system, the T18MZ-WC takes extra

time for internal processing when it is turned on/off.

When turning on the power of the transmitter

1. Place the throttle stick below 1/3 closed.

2. Turn on the power switch.

*After initialization of the transmitter is complete, the

LED monitor turns Purple.

*If your throttle stick is not at 1/3 closed or fully

closed, a warning will sound. If you move the

throttle to 1/3 closed or fully closed, the warning will

stop and will become a "Transmit ?" screen.

*If you push the button "NO", then the transmitter will

not emit radio waves.

*If you push the button "Yes", then the transmitter will

emit radio waves.

*If a battery is removed and it re-connects, please

switch on a power supply, after 3 seconds or more

pass.

Start-up time;

The time required to initialize the internal circuit

of the transmitter varies between the previous time

you turned the power off and then restarted the

transmitter. There are two “start up” modes for your

transmitter, see below:

Cold start;

If you turn on the transmitter more than four hours

after you last turned it off, the mode is “Cold start”.

³&ROGVWDUW´LVQRUPDOIRUWKH¿UVWLQLWLDOSRZHUXSRI

the day. It will take about 30 seconds to be ready for

use, as it takes time to initialize the internal circuit of

the transmitter.

Hot start;

If you turn on the transmitter less than four hours

after you last turned it off, the mode is “Hot start”.

Since initialization has been partly completed, the

transmitter will be ready to use in several seconds.

³+RWVWDUW´WDNHVSODFHXVXDOO\DWDVHFRQGÀLJKWRU

ODWHUÀLJKWLQWKHGD\

WARNING

Once you turn on the power, never shut off the

power switch until the power becomes stable (or

until the first screen shows up). If you turn off

the power switch while the transmitter is going

through the initialization process, the data could

be damaged.

Note:

The start-up time may be a little bit

slower when the SD card is installed compared

to when the card is not.

How to stop the transmitter

Turn off the power switch of the transmitter. The

internal circuit of the transmitter starts the shut down

process including saving the set-up data.

Once you turn off the power, never operate the

power switch until the power shutdown process

is fully completed. If you turn on the power

switch again while the transmitter is still in the

process of power shutdown, the data could be

damaged.

7KHULJKWVZLWFK

LVSXVKHG

,WZLOOWXUQRí

E\SXVKLQJERWK

SLHFHV

VLPXOWDQHRXVO\

,WZLOOWXUQLWRí

E\SXVKLQJRQH

VLGHIRUDOHQJWK

RIWLPH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T-18MZ-WC Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info