Bedienungsanleitung Futaba T-18MZ-WC (Seite 66 von 178) (Englisch)

747919

Zoom out

Zoom in

Vorherige Seite

1/178

Nächste Seite

＜

System Menu

＞

+(/,&237(5

$,53/$1(

*/,'(5

• Boost

The minimum current applied to the internal motor when starting the servo can be set. Since a small travel does

not start the motor, it essentially feels like the dead band was expanded. The motor can be immediately started

by adjusting the minimum current which can start the motor.

[Relationship between boost set value and servo operation]

Small

Motor reacts to a minute current and operation becomes smooth.

Large

Initial response improves and output torque increases. However, if the torque is too large, operation

will become rough.

• Boost ON/OFF

OFF : It is the boost ON at the time of low-speed operation.(In the case of usual)

ON : It is always the boost ON.(When quick operation is hope)

• Damper

The characteristic when the servo is stopped can be set.

When smaller than the standard value, the characteristic becomes an overshoot characteristic. If the value is

larger than the standard value, the brake is applied before the stop position.

Especially, when a large load is applied, overshoot, etc. are suppressed by inertia and hunting may occur,

depending on the conditions. If hunting (phenomena which cause the servo to oscillate) occurs even though the

Dead Band, Stretcher, Boost and other parameters are suitable, adjust this parameter to a value larger than the

initial value.

[Relationship between damper set value and servo operation]

Small

When you want to overshoot. Set so that hunting does not occur.

Large

When you want to operate so that braking is not applied. However, it will feel like the servo response

has worsened.

(Note) If used in the hunting state, not only will the current consumption increase, but the life of the servo will

also be shortened.

• Stretcher

The servo hold characteristic can be set. The torque which attempts to return the servo to the target position

when the current servo position has deviated from the target position can be adjusted.

This is used when stopping hunting, etc., but the holding characteristic changes as shown below.

[Relationship between stretcher and servo operation]

Small

Servo holding force becomes weaker.

Large

Servo holding force becomes stronger.

(Note) When this parameter is large, the current consumption increases.

• Buzzer

When the power supply of a servo is previously turned on at the time of a power supply injection without taking

transmit of a transmitter, the buzzer sound of about 2.5 Hz continues sounding from a servo.

(Even when the transmit of a transmitter is taken out previously, a buzzer sounds until the signal of a servo is

outputted normally, but it is not unusual.)

The transmitter has been turned OFF ahead of a servo power supply

→

The buzzer sound of about 1.25 Hz

continues sounding as servo power supply end failure alarm.

(

Do not insert or remove the servo connector while the receiver power is ON. A buzzer may

sound by incorrect recognition.

)

Buzzer sound is generated by vibrating the motor of a servo.

Since current is consumed and a servo generates heat, please do not operate the number more than needed

or do not continue sounding a buzzer for a long time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T-18MZ-WC Seite 66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info