Bedienungsanleitung Futaba T-18MZ-WC (Seite 78 von 178) (Englisch)

747919

Zoom out

Zoom in

Vorherige Seite

1/178

Nächste Seite

＜

Linkage Menu

＞

+(/,&237(5

$,53/$1(

*/,'(5

System Type selection

7KH70=:&LVIRU*+]RQO\7KHV\VWHP

can be changed from among 5 choices: FASSTest

18CH, FASSTest 12CH, FASST MULTI, FASST

7CH, S-FHSS, T-FHSS. Select the system

matched to the type of receiver you are using.u

*Even if it changes a system type, other model data is not

reset.

*If a system type is changed in the case of a helicopter, It

can choose out of two channel orders.

[Yes] : Selection sets the channel order suitable for system

type. (We recommend here.)

[No] : The present channel order is maintained.

*All control surfaces should be checked for the correct

operating directions and operating smoothness before

À\LQJWKHPRGHO

$QDORJVHUYRVFDQQRWEHXVHGZLWKWKH56%LQWKH

FASSTest 12CH mode.

Receiver linking

The receiver will only be controlled (without

being affected by other transmitters) by the

transmitter it is linked to. When using a receiver

other than one purchased as a set, linking is

necessary.

Moreover, a re-link is required when a new model

is added by model selection, and the time of

system type change.

Dual receiver function (only FASSTest 18CH

mode)

Dual receivers can be linked with the T18MZ-

:&7ZRUHFHLYHUVDUHUHFRJQL]HGLQGLYLGXDOO\

E\,'QXPEHUV)RUH[DPSOHLQ56%&+

output setting function is used, by setting the

¿UVWDVDV&+DQGVHWWLQJWKHVHFRQGDV

ŏ5HWXUQWR/LQNDJH0HQX

ŏ7RXFKWKH>6\VWHP7\SH@EXWWRQLQWKH/LQNDJH

0HQXWRFDOOWKHVHWXSVFUHHQVKRZQEHORZ

6\VWHP7\SH

6\VWHPPRGHVHWWLQJ5HFHLYHUOLQN

&+WZRVHWVRIUHFHLYHUVFDQEHXVHGDVDVHW

in the model, allowing you 16 channels. If a dual

receiver function is used, the following function can

set up individually.

・

Battery fail-safe voltage setup

A telemetry function cannot be used for the 2nd

receiver.

7KHYROWDJHDQG([WYROWDJHRIDQG

receiver cannot be known with a transmitter.

Telemetry function (only FASSTest mode)

To use the telemetry function, set “Telemetry” to

“ON”.

D/L Interval (only FASSTest mode)

When a telemetry function is enabled, the receiving

interval (down-link interval) of sensor data can be

changed.

If a D/L interval is increased, the response of

the sensor data display becomes slower, but stick

response will improve.

Battery fail-safe voltage setup (FASSTest /

T-FHSS mode)

The voltage which battery fail-safe activates, can

EHVHWZKHQ\RXOLQN97KHUHFHLYHU

PHPRUL]HVWKHVHWWLQJDVLWZDVDWOLQN

Suggested setting voltages are as follows.

FHOOV1L&GRU1L0+1RUPDOY Y

FHOOV/L)H1RUPDOY aY

FHOOV/L3R1RUPDOY aY

It is a rough reference value.

Since it changes with servos carried in the condition

and the model of a battery, please set to your own

model in a battery consumption current.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T-18MZ-WC Seite 78

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info