Bedienungsanleitung Futaba T-32MZ (Seite 30 von 189) (Englisch)

747980

Zoom out

Zoom in

Vorherige Seite

1/189

Nächste Seite

＜

Before Use

＞

A special toolbox is included with your T32MZ.

This allows you to make all of the mechanical

DGMXVWPHQWVWKDWPD\EHQHHGHG

Hexagonal wrench (1.5 mm and 2.5 mm)

7KHVHZUHQFKHVDUHIRUDGMXVWPHQWRIVWLFNVDQG

replacement of the switches.

Tool for removing switch nuts.

This is used when changing or replacing switches.

Stylus pen

A rubber cap is attached to the stylus pen/toolbox.

<RXPD\XVHWKLVVW\OXVZLWKUXEEHUFDSZKHQ

operating the touch panel. The stylus allows more

precise operation than fingers without fear of

damaging the panels surface.

ٴ<RXPD\XVHWKLVWRRO

DVDVW\OXVSHQ

Toolbox

6HUYR2SWLRQ؞7RROER[؞5HFHLYHU6ZLWFK

Receiver Switch ESW-1J

Servo (Option)

Purchase servos appropriate for their intended use.

*Analog servos may not be used when operating in the

FASSTest 12CH mode.

When operating in the FASSTest12CH mode use digital

servos, this includes all brushless and S.BUS servos.

ٴ7RROIRUUHPRYLQJ

GHFRUDWLRQQXWV

ٴ+H[:UHQFKPPDQGPP

ٴ5XEEHU&DS

ESW-1J connects a Futaba receiver to a battery and is

turned on and off in an FET circuit. Compared to using a

mechanical switch, it allows more current to be sent with

less loss.

When the model is not being used, always remove or disconnect

the battery.

■ When the switch is off, a slight amount of current still flows.

Unless the switch and battery are disconnected, the battery

will be damaged from excessive discharge.

Always make sure that the switch harness is ﬁrmly attached to

the fuselage of the model.

■ There is the danger of loss of control and crashing if the

connector is disconnected by vibration and shock.

Do not charge the receiver battery through the switch harness.

Disconnect the receiver battery and charge to the manufactures

instructions.

■ There is no charge connector in this switch.

Never reverse the battery polarity.

■ Reverse connection will immediately destroy the receiver,

servo, etc.

Ensure that the unit is mounted in an area that will eliminate

exposure to fuel, water and vibration.

■ As with any electronic components, proper precautions are

urged to prolong the life and increase the performance of the

ESW-1J.

Allow a slight amount of slack in the cables and fasten them at a

suitable location to prevent any damage from vibration during

ﬂight.

Never solder the ESW-1J or attempt to repair, deform, modify or

disassemble them.

Do not use the ESW-1J with anything other than an R/C model.

Switch

＜ Attachment ＞

Less than 5 mm of

mounting plate

Attached screw

Switch cover

Use the mounting plate from the receiver on/

off switch as a template for the cutout and screw

holes. Mount the switch on the side of the fuselage

opposite the engine exhaust, and where it won’t

be inadvertently turned on or off during handling

or storage. Be certain the switch moves without

restriction and “snaps” from ON to OFF, and that

the cutout allows full motion of the switch in both

directions.

WARNING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T-32MZ Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Futaba T-32MZ

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info