Bedienungsanleitung Futaba T-32MZ (Seite 37 von 189) (Englisch)

747980

Zoom out

Zoom in

Vorherige Seite

1/189

Nächste Seite

＜

Basic Operation

＞

+RZWRWXUQ212))WKH

SRZHURIWKHWUDQVPLWWHU

Windows

Embedded Compact 7 is installed as a

built-in operating system in the T32MZ transmitter.

Compared to the conventional system, the T32MZ

takes extra time for internal processing when it is

turned on/off.

When turning on the power of the transmitter

1. Place the throttle stick below 1/3 closed.

2. Turn on the power switch.

*After initialization of the transmitter is complete,

the LED monitor turns Purple.

*If your throttle stick is not at 1/3 closed or fully

closed, a warning will sound. If you move the

throttle to 1/3 closed or fully closed, the warning

will stop and will become a "Transmit ?" screen.

*If you push the button "NO", then the transmitter

will not emit radio waves.

*If you push the button "Yes", then the transmitter

will emit radio waves.

*If a battery is removed and it re-connects, please

switch on a power supply, after 3 seconds or more

pass.

Start-up time;

The time required to initialize the internal circuit

of the transmitter varies between the previous time

you turned the power off and then restarted the

transmitter. There are two “start up” modes for your

transmitter, see below:

Cold start;

If you turn on the transmitter more than four hours

after you last turned it off, the mode is “Cold start”.

³&ROGVWDUW´LVQRUPDOIRUWKH¿UVWLQLWLDOSRZHUXS

of the day. It will take about 30 seconds to be ready

for use, as it takes time to initialize the internal

circuit of the transmitter.

Hot start;

If you turn on the transmitter less than four hours

after you last turned it off, the mode is “Hot start”.

Since initialization has been partly completed, the

transmitter will be ready to use in several seconds.

Since initialization has been partly completed, the

transmitter will be ready to use in several seconds.

³+RWVWDUW´WDNHVSODFHXVXDOO\DWDVHFRQGÀLJKWRU

ODWHUÀLJKWLQWKHGD\

WARNING

Once you turn on the power, never shut off the

power switch until the power becomes stable (or

XQWLOWKH¿UVWVFUHHQVKRZVXS,I\RXWXUQRII

the power switch while the transmitter is going

through the initialization process, the data could

be damaged.

Note:

The start-up time may be a little bit

slower when the microSD card is installed

compared to when the card is not.

How to stop the transmitter

Turn off the power switch of the transmitter. The

internal circuit of the transmitter starts the shut

down process including saving the set-up data.

Once you turn off the power, never operate the

power switch until the power shutdown process

is fully completed. If you turn on the power

switch again while the transmitter is still in the

process of power shutdown, the data could be

damaged.

7KHFHQWHUVZLWFK

LVSXVKHG

3XVKDQGKROG

WKHFHQWHU

VZLWFK

%$6,&23(5$7,21

How to reset software

If the screen freezes for some reason and you

cannot edit, the transmitter power supply is not

fully off even if you turn OFF the power switch.

You will need to remove the battery and reinsert

it again. In this case, the power restarts in “Cold

mode”. Even though the screen freezes, all the

other functions for radio control operation remain

operative.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T-32MZ Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Futaba T-32MZ

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info