Bedienungsanleitung Futaba T-32MZ (Seite 70 von 189) (Englisch)

747980

Zoom out

Zoom in

Vorherige Seite

1/189

Nächste Seite

＜

System Menu

＞

+(/,&237(5

$,53/$1(

*/,'(5

S.BUS Servo Description of function of each parameter

*There are functions which can be used according to the kind of servo, and an impossible function.

• ID

Displays the ID of the servo whose parameters are to be read. It cannot be changed.

• Channel

Channel of the

S.BUS

system assigned to the servo. Always assign a channel before use.

• Reverse

The direction in which the servo rotates can be changed.

• Servo type

■

Normal: Normal operation mode

■

Retract: Landing gear retract mode. When a load is applied to the servo for 30 seconds without any

channel operation performed from the transmitter, the current consumption is suppressed by widening

the dead band to 40°. When channel operation is performed from the transmitter, or the servo is moved

outside the expanded dead band by an outside force, dead band expansion is reset and returns to the

original operation.

■

O.L.P. : This is the Over Load Protection mode. When a servo horn has been locked for more than 5

seconds by a load, the servo output turns off to protect the servo.

* The normal mode and retract mode are applicable only to the S3171SB, S9071SB, S9072SB,

S9074SB, and S9075SB

• Soft Start

Restricts operation in the speciﬁed direction the instant the power is turned on. By using this setting, the

ﬁrst initial movement when the power is turned on slowly moves the servo to the speciﬁed position.

• Stop Mode

The state of the servo when the servo input signal is lost can be speciﬁed. The "Hold" mode setting holds

the servo in its last commanded position even if using AM or FM system.

• Smoother

This function changes smoothness of the servo operation relative to stick movement changes. Smooth

setting is used for normal ﬂight. Select the "OFF" mode when quick operation is necessary such as 3D.

• Neutral Offset

The neutral position can be changed. When the neutral offset is large value, the servo's range of travel is

restricted on one side.

• Speed Control

Speeds can be matched by specifying the operating speed. The speed of multiple servos can be matched

without being affected by motor ﬂuctuations. This is effective for load torques below the maximum torque.

However, note that the maximum speed will not exceed what the servo is capable of even if the servos

operating voltage is increased.

• Dead band

The dead band angle at stopping can be speciﬁed.

[Relationship between dead band set value and servo operation]

Small

Dead band angle is small and the servo is immediately operated by a small signal change.

Large

Dead band angle is large and the servo does not operate at small signal changes.

(Note) If the dead band angle is too small, the servo will operate continuously and the current

consumption will increase and the life of the servo will be shortened.

• Travel Adjust

The left and right travels centered about the neutral position can be set independently.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T-32MZ Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Futaba T-32MZ

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info