Bedienungsanleitung Futaba T10 CAG (Seite 38 von 119) (Englisch)

450995

Zoom out

Zoom in

Vorherige Seite

1/119

Nächste Seite

Servo reversing (

REVERSE

): changes the direction an individual servo responds to a CONTROL STICK motion.

[Since channel 9 and 10 are switch only, its servo

REVERSE

is in the

AUX-CH

control screen with its switch assignment. See p. 46.]

For CCPM helicopters, be sure to read the section on

SWASH AFR

(p. 95) before reversing any servos.

With the exception of CCPM helicopters, always complete your servo reversing prior to any other programming.

When using

ACRO



GLID

functions that control multiple servos, such as

FLAPERON

V-TAIL

, it may be confusing to determine whether the servo needs

to be reversed or a setting in the function needs to be reversed. Refer to the

instructions for each specialized function for further details.

Always check servo direction prior to every flight as an additional

SUHFDXWLRQWRFRQ¿UPSURSHUPRGHOPHPRU\KRRNXSVDQGUDGLRIXQFWLRQ

NOTE:

THR-REV

is a special function that reverses the entire throttle control, including moving the trim functionality to

the Stick’s upper half. To use

THR-REV

, turn off the transmitter, hold down the MODE and END keys, turn on. CURSOR

DOWN to

THR-REV

and turn the DIAL to

REV

. Turn the transmitter off and back on. This change affects all models in the

radio. (

GLID

only): The separate

THR-REV

settings for each model can be set, see p.36.

GOAL of EXAMPLE: STEPS: INPUTS:

Reverse the direction of the elevator

servo.

Open

REVERSE

function.

for 1 second.

(If

ADVANCE

, again.)

REVERSE

Choose proper channel and set

direction. (Ex:

ELEV REV

)

ELEV

REV

. for 1 second.

Close.

Where next? Adjust servo travel with

END POINT

: see p. 39.

6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO

D/R

EXP

): see p. 42.

6HWXSÀLJKWWLPHUVVHHS

Set up trainer functions: see p. 47.

Logic switch selection (

LOGIC SW

): The various functions in the T10CG can be selected by switch. The Logic switch can

be assigned to the following functions:

THR-CUT

IDLE DOWN

AUX-CH

TIMER

PROG. MIX

AIRBRAKE

ELEV-FLAP

, and

AILE-

FLAP

functions. The logic switch can activate functions by two switches combinations. It is also possible to select from 2

types of logic, either AND or OR, can be selected.

Adjustability:

• Three logic switches can be used.

(Lsw1, Lsw2, and Lsw3)

• SW(1), SW(2), SW(3):

Any

SWITCH A-H or THR-STKS

• Switch position (

POSI

)

• Logic mode: AND or OR (

MODE

)

Logic combination table:

SWITCH LOGIC

SW(1) SW(2) AND OR

off off off off

off on off on

on off off on

on on on on

GOAL of EXAMPLE: STEPS: INPUTS:

Ex: Switch A and B are calculated by

AND logic. (A = down, B = down)

Open BASIC menu, then open

LOGIC

menu.

for 1 second.

(If

ADVANCE

, again.)

to 2nd page of menu.

LOGIC SW

Go to

POSI

and change setting.

(Ex:

DOWN

)

POSI

DOWN

Next,

POSI

DOWN

Repeat.

Close.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T10 CAG Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info