520093

Futaba T14-MZ Seite 26

26
Zoom out
Zoom in
Vorherige Seite
1/127
Nächste Seite
26
<Basic Operation>
How to change the frequency/How to set ID
The T14MZ system has employed the frequency
synthesizer scheme. The T14MZ transmitter will
set the frequency of the R5014DPS (PCMG3
receiver) by the wireless data transmission. When
you are to use a new PCMG3 receiver and changing
the frequency, set ID or frequency by the following
instructions.
In case of using PCMG3 r
eceivers
*Make sure that PCM-G3 is set as a modulation scheme.
Then change the frequency by the following instruction.
How to change the frequency
1. Turn on the power of the transmitter.
2. Push the area that shows the frequency in
the home screen or push the "Frequency"
button in the Linkage menu. Then the
Frequency Set screen will pop up.
3. Push the "Receiver ID" button. Then ID
inputting screen for receiver will pop up.
Input the eight-digit ID code attached to the
receiver's case. Push the "Yes" button after
confirming the ID.
*Use the "BS" button to move back digit by digit for
correction if you made a mistake. If you want to stop
changing ID code halfway, push "Return" button to return to
the previous screen.
*
Once you set the ID code for a receiver, you don't have to set
the ID code again as long as you change the receiver itself.
*When
you need to use two receivers for a large size aircraft,
you need to enter different ID codes to those receivers
respectively.
4. Push the "Band NO. (Frequency)" button if
you need to change the frequency. Then
you will see frequencies on the screen. Select
the frequency you want use. Push the button
"Yes" after confirmation. Then you will see the
"Confirmation of the change" box.
*If you have changed the module prior to turning on the
power, confirmation screen will pop up to ask you whether
you want to change the frequency. Push the button "Yes" to
change the frequency.
5. If the frequency is correct, push the button
"Yes". Then you will see the message
"Transmitting the frequency data". It takes a
certain time to send the new frequency data
to the receiver with a sound. (If you need to
resend the data, push the "Resend" button.)
6
. Turn on the power of the receiver while the
new frequency data is displayed. When
the frequency setting for the receiver is
completed, the LED monitor of the receiver
blinks once and the 1CH servo shuttles three
times across the neutral position.
*A very low power radio, whose frequency is different from
that of the channel frequency, is used to set the frequency of
the receiver. The reachable distance of the radio is designed
to be within several meters. Therefore, put the transmitter
and the receiver as close as possible when setting the
frequency of the receiver.
* If the receiver can not load the new data
due to environmental reasons, connect the
transmitter and the receiver directly by the
DSC cable. And do the procedure 6 and 7.
*LED monitor will blink on and off if the receiver's ID code
is wrong. Then move back to the Receiver ID Set screen and
restart the receiver's ID setting from the beginning.
7. Push the button "End" when the frequency
setting is completed. Then turn off the power
of the transmitter following the instructions
shown on the screen. You will be able to
use the new frequency after you turn on the
power again.
In case of using PCM1024, PPM receivers
*Make sure that PCM1024 or PPM is set as a modulation
scheme. Then change the frequency by the following
instruction.
How to change the frequency
1. Turn on the power of the transmitter.
2. Push the area that shows the frequency in
the home screen or push the "Frequency"
button in the Linkage menu. Then the
Frequency Set screen will pop up.
3. Push the "Band NO. (Frequency)" button if
you need to change the frequency. Then
you will see frequencies on the screen. Select
the frequency you want use. Push the button
"Yes" after confirmation. Then you will see the
"Confirmation of the change" box.
*If you have changed the module prior to turning on the
power, confirmation screen will pop up to ask you whether
you want to change the frequency. Push the button "Yes" to
change the frequency.
4. If the frequency is correct, push the button
"Yes". Turn off the power of the transmitter
following the instructions shown on the
screen. You will be able to use the new
frequency after you turn on the power again.
… 26 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Futaba T14-MZ wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Futaba T14-MZ

Futaba T14-MZ Kurzanleitung - Deutsch - 40 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info