Bedienungsanleitung Futaba T14-MZ (Seite 40 von 127) (Englisch)

520093

Zoom out

Zoom in

Vorherige Seite

1/127

Nächste Seite

4. Throttle cut setting

Throttle cut can be performed with one touch by

dedicated switch without changing the throttle trim

position.

Set throttle cut with the Throttle Cut function of

the Linkage Menu. After activating the throttle cut

function and selecting the switch, adjust the throttle

position so that the carburetor become full open. For

safety, the throttle cut function acts only when the

throttle stick is in the 1/3 or less (slow side) position.

5. Idle down setting

The idling speed can be lowered with one touch

with a dedicated switch without changing the throttle

trim position. Perform this setting with the Idle Down

function of the Linkage Menu. After activating the Idle

Down function and selecting the switch, adjust the

idle down speed. However, for safety, the idle down

function acts only when the throttle stick is in the 1/3

or les (slow side) position.

*While the Throttle Cut function is in operation, the Idle

Down function does not work.

6. AFR (D/R)

The AFR function adjusts the effect of the rudder

matched to the operation feeling. After setting the basic

rudder travel with the ATV function of the Linkage

Menu, adjust the rudder angle with the AFR function.

When setting D/R, rudder angle setting matched to

aerobatics can be called by switching a switch.

7. Airbrake

The airbrake function is used when the speed cannot

be increased even when the dive angle is large when

landing and taking off, etc. This function is active only

when "2 AILERON" or greater is used as the wing at

the Model Type menu of the Linkage Menu. Normally,

set this function so that both the left and right ailerons

move upward. Also complete mixing which uses

elevators to correct up/down of the nose when this

function is performed.

8. Addition of ﬂight conditions

Initial setting assigns only 1 ﬂight condition to each

model. One condition does not hinder basic flight,

but when more delicate setting is necessary at meets,

etc., use the Condition Select function of the Model

Menu to add the necessary number of conditions.

The condition selector switch, condition priority, and

condition names are also set at the same time.

After condition setting is ﬁnished, operate the switch

and check operation at the condition name displayed at

the upper right-hand side of the screen.

*When a new condition is added, "Condition1" data is

automatically copied.

Select the condition switch and set the new condition data

in the switch ON state. However, if the group mode (Gr.)

was selected in advance, the same data will be input at all

the conditions. Select the single mode (Sngl) and adjust the

condition you want to change.

9. When tailless wing model selected

Tailless wind elevator operation uses elevator→

camber mixing. This function cannot be performed at

initial setting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T14-MZ Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Futaba T14-MZ

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info