781774
26
Zoom out
Zoom in
Vorherige Seite
1/99
Nächste Seite
Original manual for petrol chainsaw FX-KSP series
Contents
Symbols used in this manual .................. 26
Symbols on chainsaw ............................. 26
Important safety information ................... 27
Noise and vibration ................................. 31
Overview ................................................. 32
Technical specifications .......................... 33
Instructions for use.................................. 34
Work techniques ..................................... 40
Maintenance and care ............................ 42
Disposal information ............................... 47
conformity ........................................ 47
Symbols used in this
manual
WARNING!
Denotes impending danger. Non-observance
of this warning may result in death or ex-
tremely severe injuries.
CAUTION!
Denotes a potentially dangerous situation.
Non-observance of this warning may result in
injury or damage to property.
NOTE
Denotes tips for operation and important in-
formation.
Symbols on chainsaw
Opening for refilling "MIX GAS-
OLINE" 40:1
Location: Above fuel cap
Opening for refilling chain oil
Location: Above oil cap
Switch notices: Pressing the
switch to the "O" (STOP) posi-
tion switches off the engine.
Location: Left side rear handle
Pulling the choke button as far as the arrow
allows the starting mode to be adjusted as fol-
lows:
Position 1 when engine is cold.
Position 0 when engine is hot.
Location: Left side rear handle
The directions indicate when
the chain brake is released
(white arrow) and activated
(black arrow).
Location: On front of chain cover
Cable starter with Easy Start
function. To start the machine,
preload the starter spring by
pulling slowly and evenly. It is
not necessary to yank it. Do
not pull beyond the dead cen-
tre point as the cable could oth-
erwise snap.
If the screw is turned with a
screwdriver in the direction of
arrow to the "MAX" position, oil
flow is stronger. Turning to the
"MIN" position results in oil flow
being weaker.
Location: On bottom rear
handle.
H = Speed increase screw, L =
Speed reduction screw, T =
Idle speed adjustment screw
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fuxtec FX-KSP250 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info