781774
38
Zoom out
Zoom in
Vorherige Seite
1/99
Nächste Seite
Original manual for petrol chainsaw FX-KSP series
Pull the starter handle until the engine
starts.
Engine starts:
Chainsaw runs at idling speed
Engine does not start:
Repeat starting procedure until engine
starts.
Slowly and surely lift the chainsaw up off
the ground. Do not touch the throttle trig-
ger when doing this!
With the left hand, pull the front hand
guard (chain brake lever) towards the front
handle and, in doing so, release the chain
brake.
The saw chain can now run freely on
the guide rail.
CAUTION!
Actuate the throttle trigger (8) only after the
chain brake has been released. The clutch
could otherwise be damaged.
The throttle trigger can now be actuated.
Before starting to saw, check the chain lu-
brication.
To do this, place the chainsaw against
a light background and open the throttle
fully.
If a slick of chain oil can be seen on the
light background (e.g. sheet of paper),
the chain lubrication is set correctly.
The chainsaw is ready for operation.
Stopping the engine
Turn the On/Off switch to the "0" position.
CAUTION!
Risk of injury!
Before switching off the chainsaw, always
allow the engine to die down!
Warm start
CAUTION!
The chainsaw is fitted with an Easy-Start
system. Do not pull the start handle quickly
or suddenly.
Block the chain brake using the front hand
guard. To do this, push the front hand
guard forwards until it is heard to engage.
Turn the stop switch to the "I" position (9).
Place the chainsaw on even ground and
secure. Step into the handle recess with
the right foot to do this.
CAUTION!
Before starting the engine:
When placing on the ground to attempt to
start the engine, ensure that the saw chain is
not in contact with the ground.
If there is ground contact while the engine is
being started there is an acute risk of acci-
dent!
Components of the chainsaw could be dam-
aged beyond repair.
Secure the chainsaw with the left hand on
the front handle.
Pull out the chainsaw's starter handle (11)
on the cable until a resistance is felt. Then
continue to pull out in doses.
Engine starts:
Chainsaw runs at idling speed
Engine does not start:
Repeat starting procedure until engine
starts.
Slowly and surely lift the chainsaw up off
the ground. Do not touch the throttle trig-
ger when doing this!
With the left hand, pull the front hand
guard (chain brake lever) towards the front
handle the chain brake can be heard to
disengage.
The saw chain can now run freely on
the guide rail.
The throttle trigger can now be actuated.
The chainsaw is ready for operation.
38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Fuxtec FX-KSP250 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info