Bedienungsanleitung Gaggenau CE492100 (Seite 23 von 24) (Englisch)

75980

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Not every malfunction can be ascribed to a defect

f your cooker. If your appliance should not function

properly, search for the fault in the list below. If you

are not successful in remedying the fault with the

aid of the list below, then contact your Gaggenau

after-sales service.

The hob does not work

Check that the household fuses for the appliance

are OK. Check if there has been a power cut.

The hob functions but does not heat up. A spot

lights constantly in the timer display.

The hob is on show room mode after installation.

Disconnect the hob from the power supply for at

least 10 seconds. Reconnect the hob and within

3 minutes carry out the following procedure:

1 Hob must be switched of at main switch. Timer

must be off.

2 Touch the symbol extension l and keep the

finger pressed down. Within 3 seconds touch

and release the main switch.

3 Remove your finger from the symbol extension.

A signal will sound. The spot in the timer

display goes off.

The hob has switched itself off

The main switch was touched accidentally. Switch

the hob back on.

u400 displa

The hob is connected incorrectly.

Disconnect the appliance from the mains using the

household fuse or the circuit breaker in the fuse

box. Call the installation technician.

E flashes in a cooking zone display

The control panel is very dirty, food has spilt over or

there is an object on the control panel. Wipe the

contr

ol panel thoroughly or remove the object.

Touch the appropriate control panel. The flashing

stops.

E f

lashes in all the cooking zone indicators and a

signal sounds

The main switch was touched continuously for more

han 5 seconds or there is an object on the main

switch. Wipe the control panel thoroughly or

remove the object. Switch the hob back on.

Er display and numbers

If an Er and numbers appear in the display, there is

a fault with the electronics. Switch the hob off and

on again using the household fuse or the circuit

breaker in the fuse box. Call the after-sales service

if the display appears again.

F2 display

The hob is too hot and has switched itself off.

Remove the pans from the cooking zones.

disappears from the display when the indicator is

acknowledged (by touching any control panel) and

when the cooking zones have cooled sufficiently.

Wait a few minutes until the cooking zones have

cooled down slightly. If

F2 appears again after the

cooking zones are switched back on, the hob is still

too hot. Switch off the cooking zones and allow to

cool further.

F4 display

The control panel is too hot and the hob has

switched itself off. Check whether there is a hot

pan on the control panel.

emove the pan from the control panel. Wait a few

minutes until the control panel has cooled down

slightly. If

F4 appears again after the cooking zones

are switched back on, call the after-sales service.

F8 display

A cooking zone has been in constant operation for

oo long. The holida

y safeguard was activated.

Switch off the cooking zone. It can be switched on

again immediately.

Trouble shooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gaggenau CE492100 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gaggenau CE492100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info