Bedienungsanleitung Gaggenau CG492111F (Seite 11 von 64) (Englisch)

760906

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

en Familiarising yourself with your appliance

Individual parts of the burners

Ensure that the individual parts of the burners are fitted

in the correct position and are straight; otherwise, this

may result in ignition problems or problems during

operation.

Fit the burner head and the burner ring in such a way

that the latches on the lower section of the burner click

into place in the corresponding slots. The alignment of

the burner head and the burner ring is not important.

Note: If the burner parts are fitted at an angle, the

appliance will not work.

Individual parts of the standard output burner and

high output burner

Individual parts of the wok burner

Ensure that the individual parts of the wok burner are

fitted in the correct position and are straight; otherwise,

this may result in ignition problems or problems during

operation. Fit the burner head such that the

thermocouple is positioned in the corresponding recess

on the burner head. The lug on the burner ring must

engage in the corresponding recess on the burner

head.

Note: If the burner parts are fitted at an angle, the

appliance will not work.

(Burner cap

0Burner ring

8Burner head

@Ignition plug

HThermocouple







(Burner cap

0Burner ring

8Burner head

@Thermocouple

HIgnition plug







Operating the appliance en

Operating the appliance

Notes

– Only use the accessories specified. Do not line the

stainless steel recess (e.g. with aluminium foil).

– The burner and ignition plug must be clean and dry.

– Only light the hotplates if the pan supports and all

burner parts are correctly fitted.

– When one burner is ignited, an ignition spark will

also be generated at all the other burners.

– Do not touch the ignition plug while the gas

appliance is being lit.

– It is important to keep the appliance clean. If the

ignition plugs are dirty, this may cause ignition

problems. Clean the ignition plugs regularly with a

small, non-metallic brush. Take care to prevent the

ignition plugs from suffering any heavy knocks.

– When you cook using a wok, place the wok ring

onto the pan support over the wok burner. Make

sure that the wok is stable on the wok ring when

you are cooking.

– When you switch from setting 3 to setting 4 or

higher, the burner will briefly switch to its maximum

output. This is to optimise ignition between the

burner rings.

– Do not cover the ventilation openings on the rear of

the gas hob.

– When the gas cooktop is switched on, the

electronics open up the gas supply, which

produces a short sound. This is normal.

– In the event of a power failure, the appliance will

not work. The gas supply is shut off.

Switching on

Your gas hob has an automatic quick-ignition function.

1Place a suitable item of cookware on the pan

support.

2Push in the control knob for your chosen burner

and turn it clockwise or anti-clockwise to the heat

setting you require.

The burner ignites automatically.

Turn the control knob to set the heat setting.

mWarning – Risk of deflagration!

If the burner does not ignite after 15 seconds, switch off

the control knob and open the door or window in the

room. Wait at least 1 minute before igniting the burner

again.

Simmer setting

With the simmer setting, the burner switches the gas

flame on and off. This allows you to melt chocolate or

heat up delicate sauces, for example.

Turn the control knob to Â. It takes 10 - 50 seconds to

switch on or off.

Electronic flame monitoring and

automatic re-ignition

For your safety, the hob has an electronic flame

monitoring system. If the flame goes out while the hob is

in use (e.g. due to a draught), the appliance will

automatically re-ignite the burner.

If re-ignition is unsuccessful (e.g. because liquid or food

has boiled over and remains on the burner), the

appliance will switch off the gas supply.The illuminated

ring behind the control knob will flash.

Turn the control knob to 0. Wait until the appliance is

cool enough and then check whether all the burner

parts are in the correct position. Check whether the

burner or the ignition plug are covered in food remnants

etc.~ "Trouble shooting" on page 15

Switching off

Turn the control knob to position 0. The appliance

electronics will shut off the gas supply.

Residual heat indicator

The luminous disc behind the control knob flashes after

switching off, to indicate that the appliance has still not

cooled down to such an extent that it can be touched

safely.

Safety shut-off

For your safety, the appliance has a safety shut-off

function.The appliance is automatically switched off if it

has been in operation for an extended period. How long

the appliance waits before switching itself off depends

on the setting (setting 12 = 1 hour, setting 1 = 4 hours).

The illuminated ring behind the control knob will flash

orange and white alternately.

Turn the control knob to 0. You will now be able to start

the appliance again as usual.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gaggenau CG492111F Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gaggenau CG492111F

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info