Bedienungsanleitung Gaggenau CI262115 (Seite 39 von 60) (Englisch)

761558

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

en Wireless temperature sensor

‚

Wireless temperature sensor

Wi reless temperature sensor

Before you use the cooking sensor functions for the

first time, connect the wireless temperature sensor to

the control panel.

Preparing and maintaining the

wireless temperature sensor

This section provides information on:

▯Adhering the silicone patch

▯Attaching the wireless cooking sensor

▯Cleaning

▯Changing the battery

Silicone patches and cooking sensors can be

purchased from specialist retailers, our technical after-

sales service or our official website. Please quote the

relevant reference number when doing so:

Adhering the silicone patch

The silicone patch secures the cooking sensor to the

cookware.

If you are using a pot with the cooking sensor functions

for the first time, attach the silicone patch directly onto

the pot. Proceed as follows:

1That the adhesive area on the pan is free from

grease. Clean the pan, dry it thoroughly and wipe

the adhesive area with a spirit.

2Remove the protective film from the silicone patch.

Adhere the silicone patch to the outside of the pan

in the correct place using the enclosed template as

a guide.

3Press down all over the surface of the silicone

patch, including in the centre.

The adhesive requires one hour to fully harden. Do not

use or clean the pan during this time.

Notes

– Do not leave the pan with the silicone patch to soak

soapy water for long periods of time.

– If the silicone patch comes off, attach a new one.

Fitting the wireless temperature sensor

Attach the temperature sensor to the silicone patch and

align it correctly.

Notes

– Make sure that the silicone patch is completely dry

before attaching the temperature sensor.

– Position the cookware in such a way that the

temperature sensor is pointing towards the outer

side of the hob.

– To prevent overheating, the temperature sensor

must not be pointed towards another item of

cookware that is hot.

– Remove the temperature sensor from the saucepan

after cooking. Store it in a clean, safe place away

from sources of heat.

– You can use up to three temperature sensors at the

same time.

Connecting the wireless temperature

sensor to the control panel

To connect the wireless cooking sensor to the control

panel, proceed as follows:

1Select the basic setting ™†; see the section

entitled ~ "Basic settings"

. The ¨ symbol lights up white.

2Touch the ¨ symbol. A signal sounds and the ¨

symbol lights up orange. The cooking zone

indicators light up white and the cooking sensor

indicators on the hotplates flash.

Briefly touch the ¨ symbol on the wireless cooking

sensor within the next 30 seconds.

00577921 Set of 5 silicone patches

CA060300 Cooking sensor and set of 5 silicone patches

Wireless temperature sensor en

3 Detection successful: The wireless temperature

sensor is detected within a few seconds. Three

short beeps sound and the ¨ symbol changes from

orange to white. The cooking sensor indicators on

the cooking zones go out.

Detection failed: Five beeps will sound. The ¨

symbol immediately changes from orange to white

and the cooking sensor indicators on the cooking

zones go out.

▯The cooking functions are made available as soon

as the wireless cooking sensor has been connected

to the control panel correctly.

▯If there is a fault with the wireless cooking sensor,

the connection may not be established correctly for

the following reasons:

– Bluetooth communication error.

– You have not pressed the ¨ symbol on the

cooking sensor within 30 seconds of selecting

the cooking zone.

– The battery in the wireless cooking sensor is

almost flat.

Reset the wireless cooking sensor and repeat the

connection procedure.

▯If there are problems with the connection due to a

transmission error, repeat the connection

procedure.

If a connection cannot be established, inform the

after-sales service.

Resetting the wireless temperature sensor

1Touch and hold the ¨ symbol for approximately 8-

10 seconds.

While you are doing this, the temperature sensor's

LED indicator will light up three times. When the

LED lights up for the third time, it will start to reset

the temperature sensor. At this point, you will need

to lift your finger off the symbol.

Once the LED goes out, this means that the

wireless temperature sensor has been reset.

2Repeat the connection procedure from point 2.

Cleaning

Do not clean the wireless temperature sensor in the

dishwasher.

Temperature sensor

Clean the temperature sensor with a damp cloth. Never

clean it in the dishwasher. Do not immerse it in water or

clean it under running water.

Remove the temperature sensor from the saucepan after

cooking. Store it in a clean, safe place (such as in its

packaging) away from sources of heat.

Silicone patch

Clean and dry before attaching to the temperature

sensor. Dishwasher safe.

Note: Cookware with the silicone patch must not be left

to soak for long periods in soapy water.

Temperature sensor window

The sensor window must always be clean and dry.

Proceed as follows:

▯Remove dirt and oil splatters regularly.

▯Use a soft cloth or cotton buds and window cleaner

for cleaning.

Notes

– Do not use abrasive cleaning agents such as

scouring pads, scrubbing brushes or cream

cleaners.

– Do not touch the sensor window with your fingers.

This may make it dirty or scratch it.

Gaggenau CI262115 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gaggenau CI262115

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info