Bedienungsanleitung Gaggenau CI282 (Seite 48 von 60) (Englisch)

703232

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

en Hood connection

Connecting appliances via your home network

If the appliances are connected to each other via your

home network, both the hood controls and Home

Connect can be used to operate the hob.

Notes

– Make sure you follow the safety instructions in the

instruction manual for your extractor hood and that

these are complied with even when operating the

appliance via the hood controls on the

hob.~

"Important safety information" on page 6

– If the appliance is being operated by means of the

controls on the extractor hood, this mode of

operation always has priority. It is not possible to

use the hood controls on the hob during this time.

– In networked standby mode, your appliance

requires a maximum of 2 W.

Setting up

To set up the connection between the hob and cooker

hood, the hob must be switched on.

Connecting directly

Make sure that the extractor hood is switched off.

For more information, refer to the section entitled

"Connecting to the hob" in the instruction manual for

your extractor hood.

Note: If you connect your hob directly to the extractor

hood, it cannot be connected to your home network as

well and you will not be able to use Home Connect.

1 Open the basic settings.

2 Touch the t symbol repeatedly until the ™“

setting appears.

‹”” will be lit on the hotplate display.

3 Set the value to ‚ using the twist knob.

‚ will flash on the hotplate display.

4 You have 2 minutes to initiate the connection

process on the extractor hood.

Once the hob is connected to the extractor hood, the

value ‹¯ appears on the hotplate display. The symbols

for the hood controls on the hob are displayed on the

hob's control panel.

Connecting via your home network

You require a router that has WPS functionality.

You require access to your router.If you do not have this,

follow the steps for "Direct connection".

When you begin, make sure that the extractor hood is on

your home network.

1 Open the basic settings.

2 Touch the t symbol repeatedly until the ™“

setting appears.

‹”” will be lit on the hotplate display.

3 Set the value to ‚ using the twist knob.

‚ will flash on the hotplate display.

4 Press the WPS button on the router within the next

2 minutes.

The hob will be connected to your home network

and the value ƒ will appear on the hotplate display.

5 Initiate the process for connecting to the extractor

hood.

Once the hob is connected to the extractor hood, the

value ‹¯ appears on the hotplate display. The symbols

for the hood controls on the hob are displayed on the

hob's control panel.

Note: Connection can only be established when both

appliances are connected to your home network and the

connection process has been initiated for both of them.

If the connection process has already timed out for one

of the two appliances, try to connect again (basic

settings, ™“ setting).

Resetting connection

You can reset the connections you have saved for your

home network and extractor hood at any time.

1 Open the basic settings.

2 Touch the t symbol repeatedly until the ™“

setting appears.

3 Set the value to ‹”” using the twist knob.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gaggenau CI282 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gaggenau CI282

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info