Bedienungsanleitung Gaggenau CI282112 (Seite 19 von 60) (Englisch)

761563

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

en Flex function

Disconnecting the two cooking zones

1Select one of the two cooking zones assigned to

the FlexZone.

2Touch the ª symbol.

3The « symbol appears in the cooking zone display.

The Flex function has been deactivated. The two

cooking zones now operate independently of one

another.

Note: If the hob is switched off, and then switched back

on again later, the flexible cooking zone is reset to

function as two independent hotplates.

FlexPlus cooking zone

The hob has two FlexPlus cooking zones which are

located between the two flexible cooking zones and

which switch on in conjunction with the right- or left-

hand flexible cooking zone. This means that larger

cooking vessels can be used and better cooking results

can be achieved.

Each FlexPlus cooking zone always switches on in

conjunction with the right- or left-hand flexible cooking

zone. It is not possible to switch them on independently

of one another.

Notes regarding cookware

The cookware should be positioned centrally for good

thermal detection and distribution.

The cookware should cover the side hotplate and the

FlexPlus cooking zone.

Depending on the size of the cookware, the flexible

cooking zone can be activated as two independent

hotplates or as one hotplate:

Set down the cookware

Elongated cookware:

Activate the flexible cooking zone

as two independent hotplates or

as one hotplate.

Large round cookware:

Activate the flexible cooking zone

as a single hotplate.

The cookware must not cover

both FlexPlus cooking zones at

the same time.

Transfer function en

Activation

1Set down the cookware on the hotplate and make

sure that it also covers the FlexPlus cooking zone.

2Select the hotplate and the required heat setting.

The hotplate and FlexPlus cooking zone indicators

light up.

The flexible cooking zone is activated.

Deactivating

Remove the cookware from the hotplate. The displays

go out.

This deactivates the FlexPlus cooking zone.

Transfer function

You can use this function to transfer the power level, set

cooking time and selected cooking sensor function from

one cooking zone to another.

To transfer the settings, move the cookware from the

cooking zone that is switched on to another cooking

zone.

This function can also be used on the flexible cooking

zones.

Note: You can find additional information on the correct

positioning of the cookware in the section on ~ "Flex

function"

1Remove any cookware from the hob.

The hotplate indicator will start flashing. The

hotplate will not heat up.

2Set down the cookware on a flexible hotplate within

the next 90 seconds. The new hotplate is detected

and the ˆ symbol lights up. The heat setting that

has been applied will flash in the hotplate display.

3Select the new hotplate within 90 seconds using

the twist knob. The settings have been transferred.





Y| [|

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gaggenau CI282112 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gaggenau CI282112

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info