Bedienungsanleitung Gaggenau CX482101 (Seite 47 von 56) (Englisch)

760864

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

en Hood control

Connecting appliances via your home network

If the appliances are connected to each other via your

home network, both the hood controls and Home

Connect can be used to operate the hob.

Notes

– Make sure you follow the safety instructions in the

instruction manual for your extractor hood and that

these are complied with even when operating the

appliance via the hood controls on the

hob.~ "Important safety information" on page 5

– If the appliance is being operated by means of the

controls on the extractor hood, this mode of

operation always has priority. It is not possible to

use the hood controls on the hob during this time.

– In networked standby mode, your appliance

requires a maximum of 2 W.

Setting up

To set up the connection between the hob and cooker

hood, the hob must be switched on.

Connecting directly

Make sure that the extractor hood is switched off.

For more information refer to the section entitled

"Connecting to the hob" in the instruction manual for

your extractor hood.

Note: If you connect your hob directly to the extractor

hood, it cannot be connected to your home network as

well and you will not be able to use Home Connect.

1To open the basic settings, touch the t symbol on

the main screen.

2Scroll left or right with your finger and select the

Hood control setting }.

3Select the Hood control option and then touch the

G symbol to confirm your choice.

4You have 2 minutes to initiate the connection

process on the extractor hood. See extractor hood

operating instructions.

Once the process is complete, a message will be

displayed, informing you of the result of the connection

process. If the connection has been successfully

established, the S symbol for ventilation control from

the hob will appear on the main screen.

If you wish to change the setting, select the Hood

control option S again and then change the setting as

required.

Connecting via your home network

You require a router that has WPS functionality.

Access to your router is required. If you do not have this,

follow the steps listed under "Direct connection".

When you begin, make sure that the extractor hood is

connected to the same home network.

1To open the basic settings, touch the t symbol on

the main screen.

2Scroll left or right with your finger and select the

Hood control setting }.

3Select the Home network option and then touch

the G symbol to confirm your choice.

4Press the WPS button on the router within the next

2 minutes.

A message will be displayed to notify you when the

hob is successfully connected to your home

network.

5You have 2 minutes to initiate the connection

process on the extractor hood. See extractor hood

operating instructions.

Once the process is complete, a message will be

displayed, informing you of the result of the connection

process. If the connection has been successfully

established, the S symbol for ventilation control from

the hob will appear on the main screen.

Note: Connection can only be established when both

appliances are connected to your home network and the

connection process has been initiated for both of them.

If the time allowed for connecting has already expired

for one of the two appliances, initiate the connection

process again.

Hood control en

Disconnecting from the network

The connection to the home network can be deleted.

1To open the basic settings, touch the t symbol on

the main screen.

2Scroll left or right with your finger and select the

Hood control setting }.

3Select the Disconnect Hood control option ‡ and

then touch the G symbol to confirm your choice.

The connections have now been deleted.

Note: The connection to the home network can be re-

established at any time.

Control the hood via the hob

In the hob's basic settings, you can configure what the

extractor hood should do when the hob or individual

cooking positions are switched on or off.

You can select other settings using the control panel.

Setting the fan

Activation

1Touch the H symbol on the main screen.

2Select the fan setting in the settings area. The

following settings are possible:

The following will also be displayed, depending on

which ventilation control setting is selected:

The selected setting will appear on the main screen next

to the H symbol.

Deactivating

Select fan setting 0.

Setting automatic mode

Activation

1Touch the H symbol on the main screen.

2Select the }Hood control option.

3Select the < Automatic option.

Depending on how the extractor hood sensor is

configured, the fan will start automatically when it

detects smoke. For additional information, see extractor

hood operating instructions.

Deactivating

1Touch the H symbol on the main screen.

2Select a different fan setting.

Setting the hood lighting

The hood light can be switched on and off using the

control panel for the cooktop.

1Touch the H symbol on the main screen.

2Select the ž Brightness option.

3Select the brightness level.

Depending on the basic settings you have selected, the

light is automatically switched on or off when the hob is

switched on or off.

0 Fan off

1, 2, 3 Fan settings.

Intensity: Low, medium, high

.Intensive mode

<Automatic mode

žFan run-on

U Unknown mode

Gaggenau CX482101 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gaggenau CX482101

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info