Bedienungsanleitung Gaggenau DVP221100 (Seite 29 von 32) (Deutsch, Englisch)

702840

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

What to do in the event of a fault

Faults often have simple explanations. Before you call

our after-sales service, please read the information in

the table below.

Note: Any repair work must only be carried out by

qualified experts. Incorrect repairs to your appliance

may present considerable risks for the user.

Fault Error Causes Possible remedy

The … symbol will appear

after a few seconds.

The vacuum cannot be

created properly.

The glass lid has not been closed

properly.

Open and close the glass lid again.

When doing so, lightly press on the

glass lid for the first few seconds.

The seal on the glass lid is not fitted

properly or is defective.

Check the seal.

The seal on the glass lid has

deformed.

Gently press the seal to straighten it

out.

The lid on the external vacuum-seal-

ing container has not been closed

properly.

Check the position of the vacuum-

sealing lid. Only use suitable vac-

uum-sealing containers.

The external vacuum-sealing con-

nection is not positioned correctly

on the vacuum-sealing chamber's

air outlet.

Check the position of the external

vacuum-sealing connection.

The … symbol will appear

after the pump has been

running for 2 minutes.

It is taking too long to cre-

ate a vacuum. Your

selected vacuum-sealing

level cannot be reached.

As the temperature rises, liquids

begin to boil. At this point, the pro-

cess of creating a vacuum stops.

Only vacuum-seal cold liquids.

If the vacuum-sealing chamber is

wet, wipe it dry.

Heat-seal the vacuum-sealing bag

early if large bubbles form.

Select a lower vacuum-sealing level.

The vacuum-sealing pro-

cess will not start. The

² symbol does not

appear even though the lid

is closed.

The appliance is not

detecting the lid.

The door switch on the glass lid is

missing or is not being detected by

the appliance.

Call the after-sales service.

If you try to operate the

appliance several times in

succession, the vacuum-

sealing process seems to

run as normal but the bag

is not heat-sealed.

The thermal switch on the heat-seal-

ing transformer has been triggered.

Allow the appliance to cool for at

least 10 minutes. Then try again.

Allow the appliance to cool for at

least 2 minutes between vacuum-

sealing operations.

The vacuum-sealing pro-

cess is taking longer and

longer.

There is too much moisture in the

pump system.

The appliance monitors the vacuum-

sealing as it progresses. If too much

liquid is retained in the pump oil,

the ¢ symbol will appear. Initiate

drying.

The pump system is extremely hot. Allow the appliance to cool and

then try again.

After the drying proce-

dure, the appliance dis-

plays the ¢ and …

symbols.

One drying cycle alone was not suf-

ficient.

Wait until the … symbol is no

longer lit up. Then start another dry-

ing cycle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gaggenau DVP221100 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gaggenau DVP221100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info