Bedienungsanleitung Gaggenau VG232234 (Seite 7 von 44) (Englisch, Portugiesisch, Spanisch)

703264

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Control knob

Special accessories

You can order the following special accessories from

your specialist dealer:

▯ SH 260 001

Hinge holder for fitting the appliance cover

▯ VD 201 014

stainless steel appliance cover

(for VG 264: two appliance covers necessary)

▯ VD 201 034

aluminium appliance cover

(for VG 264: two appliance covers necessary)

▯ VV 200 014

stainless steel connection strip for combination

with further Vario appliances

▯ VV 200 034

aluminium connection strip for combination with

further Vario appliances

Only use the accessories as specified. The

manufacturer accepts no liability if these accessories

are used incorrectly.

Burner assembly

Always assemble the burner parts correctly and evenly

to avoid faults during ignition or during use. The

catching pins on the burner ring must fit in the

corresponding holes on the burner head.

Burner assembly normal / high output burner

Operation

The markings on the control knob show the setting

between high and low heat. The flame setting is

infinitely variable between high and low heat.

Notes

‒ Only light a burner if all pan supports and burner

parts are properly assembled.

‒ Make sure the burners and ignition sparkers are

clean and dry.

‒ Fully press down the control knob and keep it

pressed, then turn it to the required position.

‒ After igniting, keep the control knob pressed for

around 2 to 4 seconds more. The thermal sensor

which controls the gas flow must be heated before

the knob can be released.

‒ If the flame should not ignite within 2 to 4 seconds,

turn the control knob further to the left to the low

heat position and then back to the high heat

position after ignition. It is often faster to ignite the

burner in the low heat position because the various

gases have a differing ignition response.

‒ Only use the recommended accessories. Do not

cover the stainless steel cooktop base (e.g. with

aluminium foil).

Switching on automatically

Your cooktop features ignition sparkers for automatic

ignition.

1 Place a suitable pot or pan on the corresponding

cooking position.

2 Fully press down the corresponding control knob

and turn it anticlockwise to the required position.

The burner lights automatically.

3 Keep the control knob pressed for a few seconds

after ignition.

The flame size can be set continuously between high

and low by slowly turning the control knob.

Switching on manually

During a power cut you can ignite the burners manually.

1 Place a suitable pot or pan on the chosen burner.

2 Press the corresponding control knob and turn it

anticlockwise to the required setting. Keep the

control knob pressed.

3 Use a gas lighter or a match to ignite the burner.

Keep the control knob pressed for a few seconds

after ignition.

The markings show the

position of the corresponding

burner and the setting

between high and low heat.

The flame setting is infinitely

variable between high and

low.

EXUQHUOLG

EXUQHUKHDG

VSDUNHU

KHDWVHQVRUIRU

IODPHPRQLWRULQJ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gaggenau VG232234 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gaggenau VG232234

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info