Bedienungsanleitung Gaggenau VI422104 (Seite 26 von 32) (Englisch)

760873

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

en Cookware test

Connecting directly

Note: If you connect your hob directly to the extractor

hood, it can no longer be connected to your home

network as well and you can no longer use Home

Connect.

1Carry out the following operating steps one after

the other without interruption.

2Push in one of the control knobs and turn it anti-

clockwise to position Ž.

3Turn the control knob clockwise to position ª

or ¹.

4Turn the control knob anti-clockwise to position 0.

The illuminated ring on the control knob lights up

blue.

5Turn the control knob clockwise to position ª

or ¹.

On the control panel, ••’ and ’‹¯‚ are

displayed alternately. The illuminated ring on the

control knob flashes blue. The hob is now ready for

registration in the home network.

6You have two minutes to initiate the connection on

the extractor hood. For more information, refer to

the section entitled "Connecting to the hob" in the

instruction manual for your extractor hood.

The connection process may take a few minutes.

The hob is connected to the extractor hood once

˜‘‚ lights up on the control panel and the

illuminated ring on the control knob lights up green.

The Ö symbol is displayed on the hob's control

panel.

Save the connection and exit the settings menu

1Carry out the following operating steps one after

the other without interruption.

2Push in the control knob and turn it anti-clockwise

to the Ž position.

3Turn the control knob clockwise to position ª

or ¹.

4Turn the control knob anti-clockwise to position 0.

The illuminated ring on the control knob goes out.

Control the hood via the hob

In the Home Connect app, you can adjust the behaviour

of your extractor hood depending on whether the hob or

individual cooking zones are switched on or off.

Cookware test

This function can be used to check the speed and

quality of the cooking process depending on the

cookware.

The result is a reference value and depends on the

properties of the cookware and the hotplate being used.

1Fill the pan with approximately 200 ml water and

place it at room temperature in the middle of the

hotplate that most closely matches the diameter of

the pan base.

2Go to the basic settings and select the ™„ setting.

‹”” will be lit.

3Touch the @ or A symbol. ‹¯ will be lit. A signal

tone will sound and the hotplate indicators will be

lit.

The function has now been activated.

¥—¯ will be lit. After a few seconds, the hotplate

displays will show the results for the quality and speed

of the cooking process.

Check the result using the following table:

To activate the function again, select the @ or A symbol.

Result

‹The cookware is not suitable for the hotplate and will

therefore not heat up.*

‚The cookware is taking longer to heat up than expected

and the cooking process is not going as well as it

should.*

ƒThe cookware is heating up correctly and the cooking

process is going well.

* If there is a smaller hotplate available, test the cookware

again on the smaller hotplate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gaggenau VI422104 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gaggenau VI422104

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info