Bedienungsanleitung Gaggia E90 (Seite 28 von 49) (Englisch)

22873

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

ENGLISH

5 - INSTALLATION

A - MAINS SUPPLY

B - DISCHARGE DUCTS

C - GAS DUCTS

D - PROTECTION SWITCH

E - MOTOR PUMP

F - PURIFIER

G - BOILER SUPPLY TAP

H - DRIP BOWL

I - GAS VALVE “Only for Machine with Gas”

L - POWER CABLE

M - MOTOR PUMP POWER SUPPLY CABLE

Before proceeding with installation check that:

- there are no bumps, signs of knocks or deformities.

1 there are no damp patches or marks which could lead one to

assume that the packaging has been exposed to the elements

2 there are no signs of tampering

Once one is satisfied that transportation has been correctly effected

proceed with installation.

Proceed with installation following the instructions according to the

sequence as described below.

5.1 WATER CONNECTION

Important: The machine must be supplied with water of

over 8°F hardness.

The installation of a water softener is recommended for

the machine water supply.

Check that the water mains to which connection is to be made

supplies drinking water.

- Connect purifier (F) to the water mains (A).

NB: before connecting the purifier to the machine, wash

out thoroughly until the water becomes clear, then proceed

to connect the purifier to the machine.

- Connect the drain cup (H) to the drainage pipe (B)

- Should the mains pressure be higher than 5 bar a pressure

reducer balanced for high pressure should be installed (device

in which any mains pressure increase does not effect the

output pressure).

5.2 ELECTRICAL CONNECTION

Important ! Before proceeding with electrical connection

it is necessary to check to ensure that the voltage rating

corresponds with that indicated on the CE plate and on the

connection plate on the power supply cable.

Check to ensure that the electrical supply line is able to support the

machine load (see chap. 4 – technical features table).

Connect to an earthing socket which complies with current

legislation.

Check that the power supply cable is efficient and that it complies

with national and European safety standards.

The user must undertake to power the machine protecting the power

line using a suitable safety switch (cut-out) that complies with the

legislation in force in the actual country itself.

Connect the power cable (L) to the electric line using a plug, or in

the case of fixed installation, using a multi-polar switch (D) for mains

separation, with a contact distance of at least 3 mm.

Connect motor pump (M) cable to motor pump (E).

For voltage change refer to the diagram shown on the general

mains switch box.

The yellow-green coloured cable MUST be connected to the room’s

earthing system.

5.3 GAS CONNECTION

“Only for Machine with GAS”

Connect valve (I) to duct (C) using a rubber hose (in compliance

with current standards) and suitable hose clamps or use the

connection supplied for stainless steel hose (as indicated in figure

in section 8 “Gas adjustment”.

Fig.5.01

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gaggia E90 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info