17
G
16
G
Problem Possible cause Remedy
Material to be chopped Cutting plate
E
not set correctly Re-adjust the cutting plate
E
is not severed sufficiently. at the cylinder. as described in “Maintaining
the Cutting Cylinder”.
Abnormal sounds, Check whether the screws Tighten the screws. Check the
Chaff Cutter rattling. are loose. the device by GARDENA Service.
Problem Possible cause Remedy
Motor will not start. Up /down switch set to Set the direction of rotation
position 0. switch to the desired position:
Material being cut is moved
upwards, e.g. if blocked
Chaff Cutter setting
Motor switches off. Blockage protection activated The motor can be switched on
due to constant overload or again after 5 minutes.
blockage at the cylinder.
Chaff Cutter not accepting Aerator direction of rotation Move the direction of rotation
material to be cut. is set incorrectly. switch
A
to the correct position.
Collection container is over-full Empty the collection container.
(cylinder blocked).
Turning direction has automati- See chapter 5.6.
cally changed due to blockage.
Cutting cylinder got stuck due Use branches to eliminate
to too wet cutting material. blockage. See chapter 6.2.
9. Faults
If you have any problem with
your Chaff Cutter, please contact
our Service, or return the defec-
tive unit together with a short
description of the problem and,
in case of guarantee, with a copy
of the receipt to one of the
GARDENA service centres listed
on the rear page.
We expressly point out that,
according to the product lia-
bility law, we are not liable for
any damage caused by our
units if, in case of repair or
exchange, other than original
GARDENA parts are used and
repair is not carried out by a
GARDENA service centre or
an authorised specialist.
The same also applies to spare
parts and accessories.
The Chaff Cutter must not be
tilted or tipped when in opera-
tion.
Do not put stones, soil, glass,
textiles, plastics or metal parts
into the Chaff Cutter.These
materials will seriously damage
the cutting tool.There is also
the danger of being hit by ma-
terial thrown back out of the
Chaff Cutter.
When the chaff cutter is
plugged in, never reach into
the ejection shaft/feeding
funnel. Danger of injury!
If foreign bodies fall into the
cylinder or if unusual sounds
or vibrations occur, switch off
the Chaff Cutter immediately
and wait until the cylinder has
stopped moving. Remove the
obstacle. Check the Chaff
Cutter for any damage / loose
parts and if necessary have
your chaff cutter repaired.
A Interruptions of Work
Never leave the Chaff Cutter
unattended at the working area.
If you interrupt your work
store the unit in a safe place.
Disconnect the mains plug!
If you wish to move the Chaff
Cutter to another place, switch
off the motor, remove the plug
and wait until the cylinder
stops moving before moving
the Chaff Cutter.
A Check the Environment
Never use the unit when it is
raining or in damp or wet areas.
Do not operate your Chaff
Cutter near swimming pools
or garden ponds.
Please observe the prescribed
local quiet times.
A Electric Safety
The Chaff Cutter must only be
operated with undamaged elec-
tric cable. If the electric cable
or the extension cable is dam-
aged disconnect the mains
plug immediately.
Check the power cable re-
gularly for damage and signs
of wear and tear.
The socket of an extension
cable should be water-proof
or the connection sockets
for extension cables must be
made of rubber or be encased
in rubber according to DIN
VDE 0620.
Only use permitted extension
cables. Ask your electrician.
For portable units, which are
used outdoors, we recommend
to use a residual-current de-
vice having a residual-current
rating
≤≤
30 mA.
In Switzerland use of a
residual-current device is
obligatory.
Description of the units:
Quiet Power Chaff Cutter
Types :
S 2000 S / S 2300 SP
Art. No.:
3980 / 3982
EU directives:
Machinery Directive 98/37/EC
Electromagnetic Compatibility
89/336/EC
Low Voltage Directive 73/23/EC
Directive 93/ 68 /EC
Directive 2000/ 14/EC
Harmonised European
standards:
EN 292-1
EN 292-2
EN 60335-1
Noise level:
measured / guaranteed
S 2000 S 95 / 96 dB (A)
S 2300 SP 95 / 97 dB (A)
Year of CE marking:
1998
Ulm, 09.11.2001
Thomas Heinl
Technical Dept. Manager
The undersigned
GARDENA Kress + Kastner GmbH · Hans-Lorenser-Str. 40 · D-89079 Ulm
hereby certifies that, when leaving our factory, the units indicated below are in accordance with the
harmonised EU guidelines, EU standards of safety and product specific standards.
This certificate becomes void if the units are modified without our approval.
EU Certificate of Conformity
