3.14.2.4 To set the lawn coverage
To set the lawn coverage follow below steps:
1. Use the left/right arrow keys to choose
Area 1, 2
or
3
.
2. Confirm by pressing the OK button.
3. Use the up/down arrow keys to change how far the
robotic lawnmower should follow the guide wire.
4. Press the right arrow key and set how often this
should be done.
5. Confirm by pressing the OK button.
6. Press the Menu button to go back to the overview
menu of Lawn coverage.
7. Continue with the settings of next
Area
.
3.14.2.5 Area 1, 2 or 3 > Disable
Each area can be disabled and enabled without having
to reenter the settings. Select
Disable
and press OK.
3.14.2.6 Area 1, 2 or 3 > More > Test
Testing selected settings can be seen as a natural part
of the installation.
Using the
Test
function, the robotic lawnmower travels
the farthest distance from the guide wire allowed by the
corridor width.
Test: Area 1, 2 or 3
To test the selected settings:
1. Place the robotic lawnmower in the charging station.
2. Use the down and the right/left arrow keys to select
the area to be tested from the
Lawn coverage
overview
screen. Press OK.
3. Select
More
and press OK.
4. Select
Test
and press OK.
5. Press the Start button and close the hatch.
6. The robotic lawnmower will now leave the charging
station and begin following the guide wire toward the
remote area. Check that the robotic lawnmower can
follow the guide wire all along the required distance.
7. The test is approved when the robotic lawnmower
can follow the guide wire to the required starting
point without any problem.
How to measure the distance to a remote area
1. Park the robotic lawnmower in the charging station.
2. In the
Area 1, 2 or 3
>
How far?
menu function, enter
a distance which beyond any doubt exceeds the real
figure. The maximum distance that can be entered is
500 metres.
3. Select
Area 1, 2 or 3
>
More
>
Test
and press OK.
4. Press the Start button and close the hatch.
5. Press STOP at the required position. The distance is
now shown in the display. This figure can now be
saved in
Area 1, 2 or 3
>
How far?
.
Area 1, 2 or 3 > More > Reset
An individual area setting can be reset to the factory
setting using this function. To reset an area setting,
select
Area 1, 2 or 3
>
More
>
Reset
using the left right
arrow keys followed by OK.
3.14.3 Installation
For many working areas there is no need to change the
factory settings but sometimes, depending on the lawn
complexity, the mowing result can be improved by
making manual settings.
3.14.3.1 Starting point
This functions allows you to control how far the robotic
lawnmower drives from the charging station before it
starts operating (mowing or lawn coverage). This is a
useful function for instance if the charging station is
placed under a veranda or in another limited space area.
Use the number keys to specify the required distance in
centimetres. The factory setting is 60 cm and the
maximum distance is 300 cm. See
First start-up on page
20
.
Note: Choosing a good starting point is important so that
the guide calibration process can be optimized.
See
Guide calibration on page 20
.
3.14.3.2 Drive past wire
The front of the robotic lawnmower always passes the
boundary wire by a specific distance before the mower
turns around. The default distance is 30 cm, but this can
be changed if required. A figure between 20 and 30 can
be selected.
Note that the distance given is only an approximate
value. In reality, the actual distance the robotic mower
passes the boundary wire can vary.
367 - 004 - 16.02.2018 Installation - 27
