Note: If the mowing results are not optimal when
using
SensorControl
, the schedule settings may need
adjusting. Do not restrict the schedule more than
necessary. Also, check that the blade disc is clean and
that the blades are in good condition.
1. Do steps 1–3 in
To get access to the menu on
page 23
.
2. Use the arrow buttons and the OK button to move
through the menu structure
SensorControl >
Cutting time
.
3. Use the arrow buttons to select
Low, Mid
or
High
frequency.
4. Push the BACK button.
3.10.6 Security level
There are 2 security levels for SILENO city and 3
security levels for SILENO life.
Function Low
Medium
(SILENO life)
High
(SILENO city)
High
(SILENO life)
Alarm
X
PIN-code
X X
Time lock
X X X
•
Alarm
- An alarm goes off if the PIN-code is not
entered within 10 seconds after the STOP button is
pushed. The alarm also goes off when the product
is lifted. The alarm stops when the PIN-code is
entered.
•
PIN-code
- The correct PIN-code must be entered
to get access to the Menu structure of the product.
If the incorrect PIN-code is entered 5 times, the
product is locked for a time. The lock is extended
for each new incorrect try.
•
Time lock
- The product locks if the PIN-code has
not been entered in 30 days. Enter the PIN-code to
get access to the product.
3.10.6.1 To set the security level
Select 1 of the security levels for your product.
1. Do steps 1–3 in
To get access to the menu on
page 23
.
2. Use the arrow buttons and the OK button to move
through the menu structure
Settings > Security >
Security level
.
3. Use the arrow buttons and the OK button to select
the level of security.
4. Push the OK button.
3.10.6.2 Security - Advanced
To make a new loop signal
The loop signal is randomly selected to create a unique
link between the product and the charging station. In
rare cases, there may be a need to make a new signal,
for instance if two adjacent installations have very
similar signals.
1. Put the product in the charging station.
2. Do steps 1–3 in
To get access to the menu on
page 23
.
3. Use the arrow buttons and the OK button to move
through the menu structure
Settings > Security >
Advanced > New loop signal
.
4. Wait for confirmation that the loop signal has been
made. This usually takes about 10 seconds.
To change the PIN-code
1. Do steps 1–3 in
To get access to the menu on
page 23
.
2. Use the arrow buttons and the OK button to move
through the menu structure
Settings > Security >
Advanced > Change PIN-code
.
3. Enter the new PIN code.
4. Push the OK button.
5. Enter the new PIN code again.
6. Push the OK button.
7. Make a note of the new PIN code. Refer to
Introduction on page 3
.
3.10.7 Lawn Coverage and CorridorCut
If the work area includes remote parts that are
connected with narrow passages, the
Lawn Coverage
and
CorridorCut
function are useful to be able to
maintain a well-cut lawn in all parts of the yard. The
Lawn Coverage
function is used to guide the product to
remote parts of the work area. The
CorridorCut
function
is used for narrow passage mowing. A guide wire must
be installed to use these functions. You can set a
maximum of 3 remote areas.
With the
Lawn Coverage
function the product first
follows and then leaves the guide wire after a certain
distance and starts to mow the lawn.
The
CorridorCut
function is suitable to mow narrow
passages of 60 cm - 1.5 m / 23 in. - 4.9 ft. width. The
product moves in a pattern to cover the passage width.
The product starts the
CorridorCut
at the set distance
from the charging station. When the product reaches the
end of the narrow passage, the product continues and
cuts the lawn as normal.
Area A, approximately 50%
Area B, approximately 30%
1298 - 015 - 20.08.2021 Installation - 25
