Bedienungsanleitung Gardena smart SILENO plus R160LiC 2018 (Seite 11 von 56) (Englisch)

687475

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

3.2 Preparations

Read through this entire chapter before beginning the

installation. How the installation is done also affects how

well the robotic lawnmower works. It is therefore

important to plan the installation carefully.

Planning is simplified if you make a sketch of the

working area, including all obstacles. This makes it

easier to see the ideal positions for the charging station,

the boundary wire and the guide wire. Draw on the

sketch where the boundary and guide wires should be

routed.

Visit www.gardena.com for further descriptions and tips

regarding installation.

1. If the lawn in the working area is longer than 10 cm

mow it using a standard lawnmower. Collect the

grass.

2. Fill in holes and hollows to stop rainwater forming

pools of water. The product may be damaged if it is

operated in pools of water. See

Guarantee terms on

page 54

3. Read carefully through all the steps before the

installation.

4. Check that all parts for the installation are included.

See

Product overview on page 5

• Robotic lawnmower

• Charging station

• Loop wire for boundary loop and guide wire

• Power supply

• Low voltage cable

• Pegs

• Connectors for the loop wire

• Screws for the charging station

• Measurement gauge

• Couplers for the loop wire

• Cable markers

3.2.1 Installation tools

During installation you will also need:

• Hammer/plastic mallet (to simplify putting the pegs

in the ground).

• Combination pliers for cutting the boundary wire and

pressing the connectors together.

• Polygrip (for pressing the couplers together).

• Edge cutter/straight spade if the boundary wire must

be buried.

3.3 Charging station

The charging station has 3 functions:

• To send control signals along the boundary wire.

• To send control signals in the guide wire so that the

robotic lawnmower can find the charging station.

• To charge the robotic lawnmower battery.

3.3.1 Best charging station location

Take the following aspects into consideration when

identifying the best location for the charging station:

• Allow minimum 3 m of free space in front of the

charging station.

• It must be possible to lay minimum 1.5 m of

boundary wire straight out to the right and left of the

charging station. Any other location can mean that

the robotic lawnmower enters the charging station

sideways and will have difficulty docking.

• It must be close to a wall socket. The supplied low

voltage cable is 10 m long.

• A level surface free from sharp objects to place the

charging station on.

• Protection from water spray for instance from

irrigation.

• Protection from direct sunlight.

• Place it in the lower part of a working area that has a

major slope.

• Possible requirement to keep the charging station

out of sight for outsiders.

The charging station must be positioned with free space

in front of it (minimum 3 m). It should also be centrally

placed in the working area to make it easier for the

robotic lawnmower to reach all areas in the working

area.

3 m / 10 ft

2 m / 7 ft

307 - 002 - 11.10.2017 Installation - 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardena smart SILENO plus R160LiC 2018 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gardena smart SILENO plus R160LiC 2018

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info