Bedienungsanleitung Gardenline 50752 (Seite 12 von 16) (Englisch)

724632

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Understanding and using these operating instructions

1200W Lawn Edger

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL: №. 50752 • 11/2018 • 50752

(toll free)

Operating instructions and safety notes!

AFTER SALES SUPPORT

(toll free)

1200W Lawn Edger

e-mail: help@powertoolsupport.com1800 909 909

MODEL: №. 50752 • 11/2018 • 50752

20 21

Changing the Blade

WARNING: Ensure the edger is switched o and is disconnected from

mains power before undertaking this task.

1. Loosen and remove the guard lock knob (15) and open the blade guard

(14). (Fig U/V)

2. Place the supplied blade spanner (24) over the outer blade ange (18) to

hold it in position, and then use a 14mm spanner (not included) to remove

the blade lock nut (17) in an anti-clockwise direction. (Fig X)

3. Remove the blade lock nut (17), outer blade ange (18) and the 190mm

serrated blade (16), and ensure the spindle and inner ange (19) are clean of

any dirt, etc. (Fig Y)

4. Fit the new 190mm serrated blade (16) then the outer blade ange (18),

then the blade lock nut (17). Using the supplied blade spanner (24) to hold

the outer blade ange in position, tighten the blade lock nut (17) using a

14mm spanner in a clockwise direction. (Fig X)

5. When the 190mm serrated blade (16) is secure, rotate it by hand to ensure

the blade is not making contact with any components of the edger. (Fig Z)

6. Close the blade guard (14), and nger tighten the guard lock knob (15). (Fig U)

NOTE: Blade wear is expected whenever you use your edger. Blades wear

quite quickly when edging along concrete paths. This does not aect the

eciency of the edger and is expected due to the aggressive abrasion of

concrete on steel.

Blades should be replaced when they become worn and no longer edge the

grass cleanly.

Replacement blades are available for purchase from our website

https://help.tools/ or by calling 1800 909 909.

X. Y. Z.

TIGHTEN

LOOSEN

Maintenance

NOTE: This product is not suitable for repair or maintenance work by the

unskilled person. The following detail explains how the blade is changed,

how the product is cleaned, and basic maintenance / safety checks. All other

maintenance work must be carried out by service agents who are experienced

with both the mechanical and electrical aspects of this product.

Safety / Deterioration Check

Any of the following faults found should be investigated and repaired by a

qualied service agent or a similarly qualied person in order to avoid hazard:

• Prior to each use or during the cleaning operation check the following with

the 240V ac mains power DISCONNECTED from the product.

• Check the guard is rmly mounted and the swing door locates, closes and

locks correctly.

• Check the guard is not cracked or fractured.

The following checks should be made with the 240V ac mains supply

connected:

• BE AWARE and take precautions as the blade will rotate under some of the

checks. Tests should be made on soft ground with the blade clear of the

ground.

• Gently depress the trigger switch (2) without the safety lock button (3)

being depressed. The product should not start. (Do Not use the product if

the unit starts without the safety lock button (3) not pressed).

• Press the safety lock button (3) and the trigger switch (2) to start the edger.

Release the trigger switch (2). The unit MUST stop. If the unit fails to stop,

remove the plug from the 240V ac mains supply. (DO NOT use the product

in this condition).

• On start up, the motor and the blade rotation should be an even growling

noise. If there is a grinding, or squealing noise, or uneven speed, turn o the

edger, disconnect and have the unit serviced by a qualied service agent or

a similarly qualied person in order to avoid hazard.

The following faults, if found, can be corrected by the owner of the edger,

unless the fault requires disassembly, which must be performed by a qualied

service agent or a similarly qualied person in order to avoid hazard.

• Check the wheels freely turn without binding.

• Check the height adjustment is fully located and rmly clamped by the

height adjustment knob (21).

• Check there is no build up of grass around the spindle.

• Check the blade size and cutting edge of the blade. Replace the blade if

necessary per the instructions to follow.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardenline 50752 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info