Bedienungsanleitung Gardenline BC35TS-2 (Seite 14 von 26) (Englisch)

724647

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

31cc Brushcutter / Line Trimmer

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL: №. BC35TS-2 • 08/2018 • 49290

(toll free)

AFTER SALES SUPPORT

(toll free)

31cc Brushcutter / Line Trimmer

e-mail: help@powertoolsupport.com1800 909 909

MODEL: №. BC35TS-2 • 08/2018 • 49290

24 25

1. Lay the unit down so that the fuel tank bracket

(39) is on the ground or on a secure surface.

Lift the gearbox end of the lower shaft (15) to

gain access to the output spindle (20).

2. Line up the tabs on the clip-on line trimmer

guard attachment (33) with the large slots on the

brushcutter guard (17). There are 2 main release

clips; one on each end of the clip-on line

trimmer guard attachment (33). This needs to

line up with the large slots on the brushcutter

guard (17) (Fig AJ).

3. When all tabs are lined up in position, push the

tabs on the clip-on line trimmer guard

attachment (33) into the slots, and the release

clips into the large slots. You will hear clicks

when the release clips are secure. (Fig. AK)

NOTE: Before using the line trimmer, remove the

cut o blade protector. After using the line

trimmer, it is recommended to replace the

blade protector.

4. To fully secure the clip-on line trimmer guard

attachment (33) to the brushcutter guard (17),

insert and secure the screw using the supplied

spark plug spanner / blade nut wrench /

screwdriver combination (36), using the

screwdriver end of the tool. Secure until tight (Fig AL).

Fitting the Spool and Line Assembly on the Line Trimmer

NOTE: If the unit has been used as a brushcutter rst, the brushcutter blade

will need to be removed before tting the spool and line assembly.

Refer to “Changing/Removing the Brushcutter Blade” for instructions on how

to remove the blade on page 22.

NOTE: Always ensure the engine is turned o before undertaking this assembly.

1. Lay the unit down so that the fuel tank bracket (39) is on the ground or on

a secure surface. Lift the gearbox end of the lower shaft (15) to gain access

to the spindle (20).

AJ.

AK.

AL.

IMPORTANT: Ensure the inner ange is mounted on the spindle of the line

trimmer. The outer ange (29), the protector (27), the 3T brushcutter blade

(28) and the blade nut (26) are NOT required when the line trimmer spool

& line assembly (35) is being tted.

Keep these components in a safe place. The 3T

brushcutter blade (28) should be placed back in

the cardboard packaging/envelope.

2. Place the spool and line assembly (35) on the

spindle (20) and thread on to the spindle nger

tight in an anti clockwise direction all the way

down until the back of the spool makes contact

with the inner ange (30) (Fig AM),

3. Insert the long end of the supplied 4mm allen

key (37) through the spindle lock entry hole (19)

and into the hole on the inner ange (30).

(This locks the spindle allowing the spool and

line assembly (35) to be secured). Further tighten

the spool and line assembly (35) ensuring the

assembly is tight on the spindle (20) and inner

ange (30) before removing the 4mm allen key

from the spindle hole to release the spindle

being locked (Fig. AN).

Removing the Spool and Line Assembly

NOTE: Always ensure the engine is turned o before undertaking this assembly.

1. Lay the unit down so that the fuel tank bracket (39) is on the ground or

on a secure surface. Lift the gearbox end of the lower shaft (15) to gain

access to the output spindle (20).

2. Insert the long end of the supplied 4mm allen key (37) through the

spindle lock entry hole (19) and into the hole on the inner ange (30).

(This locks the spindle allowing the spool and line assembly to be

removed). (Fig. AN)

3. Loosen the spool and line assembly (35) in a clockwise direction until it

can be removed from the spindle (20). Remove the allen key (37) locking

the spindle (20) once the spool and line assembly (35) has been removed.

AN.

AM.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardenline BC35TS-2 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info