Bedienungsanleitung Garmin AIS 600 (Seite 5 von 12) (Englisch)

501979

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

AIS 600 Instructions 5

Installing the AIS 600

Use the following instructions to install the AIS 600 device. Details for the following steps are included in this document:

1. Select locations for the AIS components.

2. Mount the AIS 600 transceiver box.

3. Wire the AIS 600 to power.

4. Install and connect the GA 38 GPS antenna (page 6).

5. Connect the AIS 600 to a VHF antenna and to an optional VHF radio (page 7).

6. Connect the AIS 600 to a NMEA 2000 network or to a NMEA 0183-compatible chartplotter (optional - page 7).

7. Add a silent-mode switch or a Safety Related Message (SRM) switch (optional - page 8).

Selecting Locations for the AIS 600 Components

Use the wiring layout diagrams starting on page 3 to determine how to best organize the AIS 600 components on your boat. Ensure that the

cables reach all components before permanently mounting any component.

Mounting the AIS 600 Transceiver Box

Install the AIS 600 transceiver box below deck on a bulkhead. Select a location that is dry and protected from washdown. Ensure that the

location is well ventilated and away from objects that generate heat. Ensure that the transceiver box is at least 15

in. (40 cm) from any

compass to avoid interference.

Needed Tools

• Drill and drill bits

• Number 2 Phillips screwdriver

To mount the transceiver box:

1. Ensure that the chosen location is dry, protected, and well-ventilated.

2. Use the transceiver box as a template, and use a pencil to mark the holes in the four corners. Do not drill through the transceiver box.

3. Drill four

in. (3 mm) pilot holes.

4. Mount the transceiver box using the included M4.2 × 25 screws. You can also use bolts, washers, and nuts (not included) to mount the

transceiver box if the mounting surface is suitable.

Connecting the Transceiver Box to Power

Use the AIS 600 power/data cable to connect the transceiver box to a 12 or 24

Vdc battery.

Notes:

• Use the AIS 600 Power Wiring-Assignment Table to identify the positive and

negative wires.

• The replacement fuse on the power/data wiring harness is a 5 A, fast-acting fuse.

• If it is necessary to extend the power wires, use 16 AWG or larger wire.

Installing the AIS 600 Power Toggle

The AIS 600 can be powered on and off in one of 3 ways:

• If the AIS 600 is connected to a NMEA 2000 network, it will toggle on and off with the NMEA 2000 network.

NOTE: The AIS 600 is not powered by the NMEA 2000 network, although it will turn on when it detects power on the NMEA 2000

network. You must connect the AIS 600 to power, and not just to the NMEA 2000 network.

• If the AIS 600 is wired to a Garmin chartplotter using NMEA 0183, connect the yellow wire from the AIS 600 power/data cable to the

Accessory On wire from the chartplotter. The AIS 600 will then toggle on or off with the Garmin chartplotter.

Device Wire Color Function

AIS 600 power/data

cable

Red Power—positive (+)

Black Ground—negative (-)

AIS 600 Power Wiring-Assignment Table

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin AIS 600 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin AIS 600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info