Bedienungsanleitung Garmin AIS 800 (Seite 1 von 4) (Englisch)

691461

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

AIS 800

INSTALLATION

INSTRUCTIONS

Important Safety Information

WARNING

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

CAUTION

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

FCC Compliance

NOTICE

In the USA, it is prohibited under FCC regulations to enter

incorrect or improper data, and it is prohibited for any person

other than the manufacturer or the installing dealer to input

MMSI number.

It is a violation of the rules of the FCC to input an MMSI number

that has not been properly assigned to the user, or to otherwise

input any inaccurate data in this device.

Assigning Data to the Device

You must program the AIS 800 device with a valid vessel MMSI

number before installing the device on your boat. The device

operates in silent mode without a valid MMSI number. In silent

mode, the device receives AIS signals, but does not transmit

position data. You can program the device to transmit static

vessel data including the vessel name, call sign, type, and

dimensions, which can include the location of your boat's GPS

antenna.

Installing the AIS 800 Software on Your Computer

Go to www.garmin.com/AIS800, select Software, and

download the .zip file to your computer.

Connect the included USB cable to your computer and the

USB port on the AIS 800 device.

NOTE: While you program with the USB cable, you may

need to disconnect all other cables from the AIS 800 device

to prevent a ground loop between the computer and your

vessel power.

Double-click the .exe file, and follow the on-screen

instructions.

Programming the AIS 800

Before the device can be used on a boat, it must be

programmed with a unique MMSI number and with additional

vessel-specific static data. The MMSI number must be

programmed by an authorized marine electronics dealer or

installer.

Before you can program the device, you must install the AIS 800

software on your computer (Installing the AIS 800 Software on

Your Computer, page 1).

In the program, select the Static data tab.

In the Connection and Status window, select a COM port

from the drop-down list.

Select Connect.

Enter your ship name, call sign, dimensions, vessel type, and

MMSI number (Assigning an MMSI Number to the AIS 800,

page 1).

Select Save data to AIS 800.

NOTE: The data is lost if the AIS 800 device is turned off.

You must select Save data to AIS 800 to permanently save

your data.

Select File > Exit.

Assigning an MMSI Number to the AIS 800

Launch the AIS 800 setup software.

In the Connection and Status window, select a COM port

from the drop-down list.

Select Connect.

In the Static Data window, enter your nine-digit MMSI

number in the MMSI Number field.

NOTICE

You cannot change the MMSI number after you assign the

MMSI number to your boat. If you assign an incorrect MMSI

number, you must return the device to the manufacturer for a

factory reset.

Select Save data to AIS 800.

Tools Needed

• Drill

• Drill bits appropriate for the surface and hardware

• Phillips screwdriver

• Pencil

Mounting Considerations

NOTICE

This device should be mounted in a location that is not exposed

to extreme temperatures or conditions. The temperature range

for this device is listed in the product specifications. Extended

exposure to temperatures exceeding the specified temperature

range, in storage or operating conditions, may cause device

failure. Extreme-temperature-induced damage and related

consequences are not covered by the warranty.

• You must mount the device in a location where it will not be

submerged.

• You must mount the device in a location with adequate

ventilation where it will not be exposed to extreme

temperatures.

For optimal internal GPS reception:

• You should mount the device in a location where it is above

the water line when the ship is in the water.

• You should mount the device as far as possible, at least

20 cm (7.9 in.), from cables, electronics, metal objects, and

other potential sources of GPS interference.

• If you mount the device in a boat with a metal hull, you must

connect the device to an external GPS antenna (sold

separately).

• If possible, you should mount the device horizontally, with the

face of the device pointing upward or vertically with the LEDs

facing upward. The GPS is most sensitive in these positions.

VHF Antenna Mounting and EME Exposure

WARNING

Radio operators with cardiac pacemakers, life-support

machines, or electrical medical equipment should not be

exposed to excessive radio-frequency (RF) fields, because the

RF field may interfere with the function of their medical

equipment.

June 2019

190-02422-91_0D

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin AIS 800 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin AIS 800

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info