Bedienungsanleitung Garmin Alpha100 TT 10 (Seite 12 von 26) (Englisch)

657463

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

dog as long as the key is held, for a maximum of 8 seconds.

Your stimulations should typically be far shorter than 8 seconds.

Continuous stimulation can be useful when first starting training

with your dog.

You can also train using a tone (T). When you select T for a

key, the key press activates an audible tone instead of

stimulation. Using the tone can be a helpful training tool.

NOTE: The tone volume cannot be changed. Changing the

intensity of the tone does not adjust the volume.

Choosing the Correct Intensity Level

Set the training keys to the lowest level (page 6).

Press a training key.

Observe the dog for a reaction, such as a head shake, neck

movement, or just a change in expression.

Sometimes dogs will vocalize due to the surprise of the

electrical stimulation. If the dog vocalizes more than once,

the intensity level is too high for beginning training.

If there is no reaction, increase the intensity level by one

level until the dog has a slight but recognizable reaction to

the stimulation.

The intensity level that causes a slight but recognizable reaction

is your dog's baseline level for beginning collar training. You do

not need to, and should not, apply this intensity selection test

again.

After you begin training, the dog’s performance guides your

intensity selection. As the dog advances in training, you may

need to change the level depending upon the training situation.

Training the Dog to Heel and Sit with the Collar

Before you begin training your dog using the collar, your dog

must show a grasp of the "heel," "sit," and "come" commands

while on the leash, you must put on the collar (page 4), and you

must find the correct intensity level (page 8).

When beginning collar training, start with the "heel" and "sit"

commands.

With the dog at your side on a leash, pull up on the leash,

and command the dog to "sit."

If the dog does not sit immediately, press a training key

briefly, and repeat the command to "sit."

Reward the dog with praise when the dog obeys the

command.

After the dog begins obeying the "sit" command without

collar stimulation, you should move on to the "heel"

command.

With the dog at your side on a leash and with the collar on,

command “heel” and begin walking forward while gently

pulling on the leash.

If the dog not heel, press a training key briefly, repeat the

command to “heel”, and move in another direction or pull

back on the leash.

Reward the dog with praise when the dog obeys the

command.

Training the Dog to Come Here with the Collar

Before you begin training your dog to come "here" using the

collar, your dog must have a strong grasp of the "heel" and "sit"

commands using the collar, you must put on the collar (page 4),

and you must find the correct intensity level (page 8). Also, you

may need to use a long leash to effectively train "here."

With the dog in a sitting position, move away to the end of

the leash.

Command the dog to come “here.”

If the dog does not move immediately toward you, press a

training key briefly, gently tug on the leash, and repeat the

command to come "here."

Reward the dog with praise as soon as the dog begins to

move toward you.

If the dog begins to veer away, press a training key briefly,

and repeat the command to come "here."

Contact Tracking

You can track other hunters so you know where they are at all

times. You can also send messages to your contacts. One

Alpha handheld device can track up to 20 devices (TT dog

collar devices and Alpha handheld devices).

Adding a Contact Over MURS/VHF

Before you can add a contact over MURS/VHF, you should be

near the contact, for best results.

You can add fellow hunters to your handheld device so you can

track them on the map (page 8) and send messages to them

(page 8).

On your handheld device, select > Contacts > Add.

Bring the two handheld devices near each other, and select

Yes on your handheld device.

On the contact's handheld device, select > Contacts >

Pair.

On your handheld device, enter the name of the contact, and

select > OK.

The contact is added to your handheld device.

If you would like to be added to the hunter's handheld device,

repeat this procedure using the hunter's handheld device.

Adding a Contact Using the ID

Before you can add a hunter using the contact ID, you must

have the hunter find the contact ID (page 8) and send it to

you.

If you are not nearby the hunter you want to add, you can add

the hunter using the contact ID.

On your handheld device, select > Contacts > Add.

When asked if you are near the other handheld device,

select No.

When asked if you know the ID, select Yes.

Select the correct ID for the contact you are adding.

Enter the name of the contact, and select > OK.

The contact is added to your handheld device.

If you would like to be added to another hunter's handheld

device using your contact ID, repeat this procedure using the

hunter's handheld device.

Sending a Message to Your Contacts

You can send and receive automated messages. There are 18

messages choose from, such as "Help" and "I'm Coming."

Select > Contacts > Message.

Select a message.

The message is sent to your contacts with your name before the

message. Anyone tracking your handheld device receives the

message.

Tracking a Contact

You can keep track of contacts' locations using the map.

Select .

Finding Your Contact ID

Select Setup > Contacts > Pairing Setup.

The contact ID for your handheld device is listed under ID.

8 Contact Tracking

Garmin Alpha100 TT 10 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info