Bedienungsanleitung Garmin BarkLimiter Deluxe (Seite 4 von 8) (Englisch)

691419

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Fitting the Collar on Your Dog

CAUTION

To prevent irritation from the contact points, remove the collar

for at least eight hours out of every 24-hour period.

This device is not intended for human use. Do not attempt to

use on any person.

NOTICE

Before you put the collar on the dog, remove the charging clip. If

you do not remove the clip, it may become detached from the

collar and become lost.

In order to properly detect and correct barks, the collar and

device must fit the dog properly. If the collar is too loose or

positioned incorrectly, bark corrections may be inconsistent.

This can delay or prevent the dog from learning not to bark.

Place the collar around the middle of the dog's neck.

Position the device at the front of the dog's neck, with the

status LED facing towards the dog's chin and the contact

points against the throat.

TIP: The device contact points should be positioned near the

dog's vocal cords. This location varies based on the breed of

dog. If the device does not seem to detect the dog's barks,

you should move the device closer to or further from the

dog's body to find the ideal location.

Tighten the strap so that it is very snug around the dog's

neck, and fasten the buckle.

NOTE: The collar should fit tightly and should not be able to

rotate or slide on the dog's neck. The dog must be able to

swallow food and water normally. You should observe your

dog's behavior to verify that the collar is not too tight.

Wiggle the device to work the contact points through the

dog's coat.

NOTE: The contact points must have contact with the dog's

skin to effectively detect and correct barks.

If the strap is too long, cut off the excess, leaving at least

3 in. (8 cm) to spare.

TIP: You can mark the hole used to fasten the buckle for

future reference.

Changing the Bark Correction Mode and

Intensity Level

Rotate the dial to select an option:

• To correct using vibration, select V (page 2).

• To correct using automatic intensity, select A (page 2).

• To correct using a set intensity level, select 1 to 7

(page 2).

A higher number indicates a higher intensity level.

Vibration

The device can use a short vibration to correct the dog. When

using vibration, no electrical stimulation is used.

Automatic Intensity

The device can set the stimulation intensity level automatically

based on the barking behavior of the dog. The device starts at

the lowest intensity level and increases the intensity level

gradually until the dog stops barking. When the dog is quiet, the

intensity decreases over time.

The automatic intensity feature is designed to eliminate

excessive nuisance barking. To stop barks more immediately,

you should set the intensity level manually.

Choosing the Correct Intensity Level

CAUTION

To prevent irritation from the contact points, remove the collar

for at least eight hours out of every 24-hour period.

You can set the stimulation intensity level manually from 1 to 7.

You should choose the lowest intensity level that discourages

the dog from barking. If you have never used a bark correction

collar with the dog, the dog requires time and experience to

learn that the bark is the cause of the stimulation.

Set the intensity to the lowest level.

For thirty minutes, when the dog barks, observe the dog for a

reaction, such as a head shake, neck movement, a change

in the way the dog barks, or just a change in expression.

If there is no reaction, increase the intensity by one level until

the dog has a slight but recognizable reaction to the

stimulation.

Allow 24 hours for the dog to learn to respond by not barking.

If the dog continues barking while wearing the collar,

increase the intensity level gradually until you find the level

that discourages the dog from barking.

Bark Odometer™

When you turn off the device, the LED flashes red and green to

report the number of times the device detected a bark since it

was last turned on. This can help you track your dog's barking

behavior.

Red flash 10 barks

Green flash 1 bark

For example, one red flash followed by four green flashes

indicates the device detected 14 barks.

Checking the Bark Odometer

Remove the device from the dog.

Position the device so that you can see the status LED.

Rotate the dial to N.

Count the red and green flashes.

Troubleshooting

My device does not seem to be active

When the device is active, the status LED flashes only when the

device detects a bark or motion.

• Verify the collar is turned on (page 1).

• Verify the battery is not low (page 3).

• Remove the device from the dog, and shake the device

briefly.

When the device is active, the device detects the motion,

and the status LED flashes.

2 Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin BarkLimiter Deluxe Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin BarkLimiter Deluxe

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info