Bedienungsanleitung Garmin Drive 5 (Seite 4 von 16) (Englisch)

698355

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Press the suction cup to the windshield, and flip the lever

back toward the windshield.

Fit the tab on the top of the mount into the slot on the back of

the device.

Press the bottom of the mount into the device until it clicks.

Plug the other end of the vehicle power cable into a power

outlet in your vehicle.

Turning the Device On or Off

• To turn the device on, press the power key, or connect the

device to power.

• To put the device in power saving mode, press the power key

while the device is on.

While in power saving mode, the screen is off and the device

uses very little power, but it can wake instantly for use.

TIP: You can charge your device faster by putting it in power

saving mode while charging the battery.

• To turn off the device completely, hold the power key until a

prompt appears on the screen, and select Off.

The prompt appears after five seconds. If you release the

power key before the prompt appears, the device enters

power saving mode.

Acquiring GPS Signals

When you turn on your navigation device, the GPS receiver

must collect satellite data and establish the current location.

in the status bar indicates the satellite signal strength. The time

required to acquire satellite signals varies based on several

factors, including how far you are from the location where you

last used your navigation device, whether you have a clear view

of the sky, and how long it has been since you last used your

navigation device. The first time you turn on your navigation

device, it may take several minutes to acquire satellite signals.

Turn on the device.

Wait while the device locates satellites.

If necessary, go outdoors to an open area, away from tall

buildings and trees.

When turns green, the device has acquired satellite signals

and is ready for navigation.

Status Bar Icons

The status bar is located at the top of the main menu. The status

bar icons display information about features on the device. You

can select some icons to change settings or view additional

information.

GPS signal status. Hold to view GPS accuracy and acquired

satellite information (Viewing GPS Signal Status, page 13).

Current time. Select to set the time (Setting the Time,

page 11).

Battery charge level.

Using the On-Screen Buttons

On-screen buttons allow you to navigate the pages, menus, and

menu options on your device.

• Select to return to the previous menu screen.

• Hold to quickly return to the main menu.

• Select or to scroll through lists or menus.

• Hold or to scroll faster.

• Select to see a context-based menu of options for the

current screen.

Adjusting the Volume

Select Volume.

Select an option:

• Use the slider bar to adjust the volume.

• Select to mute the device.

• Select for additional options.

Adjusting the Screen Brightness

Select Settings > Display > Brightness.

Use the slider bar to adjust the brightness.

Driver Awareness Features and Alerts

NOTICE

The driver alerts and speed limit features are for information

only and do not replace your responsibility to abide by all posted

speed limit signs and to use safe driving judgment at all times.

Garmin is not responsible for any traffic fines or citations you

receive for failing to follow all applicable traffic laws and signs.

Your device provides features that can help encourage safer

driving and increase efficiency, even when you are driving in a

familiar area. The device plays an audible tone or message and

displays information for each alert. You can enable or disable

the audible tone or message for each type of alert. Not all alerts

are available in all areas.

School zone or nearby school: The device plays a tone and

displays the distance to and speed limit (if available) for an

upcoming school or school zone.

Speed limit reduction: The device plays a tone and displays

the upcoming reduced speed limit so you can be prepared to

reduce your speed.

Speed limit exceeded: The device plays a tone and displays a

red border on the speed limit icon when you exceed the

posted speed limit for the current road.

Wrong way on a one-way street: The device plays a message

and displays a full-screen warning if you travel the wrong way

on a one-way street. The edges of the screen appear red and

an alert remains at the top of the screen until you leave the

one-way street or correct your direction of travel.

Railroad crossing: The device plays a tone and displays the

distance to an upcoming railroad crossing.

Animal crossing: The device plays a tone and displays the

distance to an upcoming animal crossing area.

Curve: The device plays a tone and displays the distance to a

curve in the road.

Slower traffic: The device plays a tone and displays the

distance to slower traffic when you approach slower traffic at

a higher speed. Your device must be receiving traffic

information to use this feature (Receiving Traffic Data Using

a Traffic Receiver, page 9).

Fatigue warning: The device plays a tone and suggests

upcoming rest stops after you have been driving for more

than two hours without stopping.

Enabling or Disabling Audible Driver Alerts

You can turn off individual audible driver alerts. The visual alert

appears even when the audible alert is disabled.

Select Settings > Map & Vehicle > Audible Driver Alerts.

Select or clear the check box next to each alert.

Red Light and Speed Cameras

NOTICE

Garmin is not responsible for the accuracy of or the

consequences of using a red light or speed camera database.

2 Driver Awareness Features and Alerts

Garmin Drive 5 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Drive 5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info