Bedienungsanleitung Garmin DriveAssist 50 (Seite 22 von 30) (Englisch)

650682

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Select a map.

Navigation Settings

Select Settings > Navigation.

Route Preview: Shows a preview of the major roads in your

route when you start navigation.

Calculation Mode: Sets the route calculation method.

Fatigue Warning: Alerts you when you have been driving for a

long period without a break.

Avoidances: Sets road features to avoid on a route.

Custom Avoidances: Allows you to avoid specific roads or

areas.

Environmental Zones: Sets the avoidance preferences for

areas with environmental or emissions restrictions that may

apply to your vehicle.

Toll Roads: Sets preferences for avoiding toll roads.

Tolls and Fees: Sets preferences for avoiding toll roads and toll

stickers.

NOTE: This feature is not available in all areas.

Restricted Mode: Disables all functions that require significant

operator attention and could become a distraction while

driving.

GPS Simulator: Stops the device from receiving a GPS signal,

and saves battery power.

Calculation Mode Settings

Select Settings > Navigation > Calculation Mode.

The route calculation is based on road speeds and vehicle

acceleration data for a given route.

Faster Time: Calculates routes that are faster to drive but can

be longer in distance.

Shorter Distance: Calculates routes that are shorter in distance

but can take more time to drive.

Off Road: Calculates a direct line from your location to your

destination.

Setting a Simulated Location

If you are indoors or not receiving satellite signals, you can use

the GPS to set a simulated location.

Select Settings > Navigation > GPS Simulator.

From the main menu, select View Map.

Tap the map twice to select an area.

The address of the location appears at the bottom of the

screen.

Select the location description.

Select Set Location.

Camera Settings

Select Settings > Camera.

Garmin Real Vision™: Displays a camera view when

approaching some destinations (Destination Arrival with

Garmin Real Vision

™

Assistance, page 6).

Forward Collision Warning: Alerts you when the device

detects you are following too closely to the vehicle in front of

you (Forward Collision Warning System, page 4).

Forward Collision Sensitivity: Allows you to set the sensitivity

of the forward collision warning. A higher sensitivity alerts you

sooner than a lower sensitivity.

Lane Departure Warning: Alerts you when the device detects

you may be crossing a lane boundary unintentionally (Lane

Departure Warning System, page 4).

Camera Placement: Allows you to indicate the placement of

your device in the vehicle.

Vehicle Height: Allows you to specify the class of vehicle in

which the device is installed. This helps improve the accuracy

of driver assistance features, especially when using the

device in a van, truck, or other tall vehicle.

Go Alert: Alerts you when stopped traffic starts moving (Go

Alert, page 4).

Record on Startup: Enables the dash camera to start recording

video automatically when you turn on the device.

Automatic Incident Detection: Saves video automatically when

the device detects a possible driving incident.

Data Overlay: Includes date, time, location, and speed

information in the recorded video.

Video Resolution: Sets the resolution and quality for video

recordings.

Record After Power Loss: Continues recording video up to a

selected time period after external power is lost.

Backup Camera Settings

The backup camera settings allow you to manage paired

Garmin backup cameras and camera settings. This menu

appears on your navigation device only when the device is

connected to a wireless camera receiver cable. See the owner's

manual for your backup camera for detailed information about

pairing cameras and camera settings. Go to garmin.com

/backupcamera to purchase a Garmin backup camera.

Select Settings > Backup Camera, and select a paired camera.

Unpair: Removes the paired camera. You must pair the camera

again before you can view it using this device and cable.

Rename: Allows you to rename the paired camera.

Guidance Lines: Shows or hides guidance lines and allows you

to adjust the position of the guidance lines.

babyCam Settings

The babyCam settings allow you to manage paired Garmin

babyCam

™

cameras and camera settings. This menu appears

on your navigation device only when the device is connected to

a wireless camera receiver cable. See the owner's manual for

your camera for detailed information about pairing cameras and

camera settings. Go to garmin.com/babycam to purchase a

Garmin babyCam camera.

Select Settings > babyCam, and select a paired camera.

Power Settings: Allows you to set the amount of time the video

appears on the screen.

Flip Video: Allows you to flip or mirror the video.

Alignment: Displays the babyCam video to help you align the

camera.

Check Seat Reminder: Enables a reminder to check for rear

seat passengers before exiting the vehicle.

Unpair: Removes the paired camera.

Rename: Allows you to rename the paired camera.

Bluetooth Settings

Select Settings > Bluetooth.

Bluetooth: Enables Bluetooth wireless technology.

Search for Devices: Searches for nearby Bluetooth devices.

Friendly Name: Allows you to enter a friendly name that

identifies your device on other devices with Bluetooth

wireless technology.

Disabling Bluetooth

Select Settings > Bluetooth.

Select Bluetooth.

18 Customizing the Device

Garmin DriveAssist 50 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin DriveAssist 50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info