Bedienungsanleitung Garmin Echo 100 (Seite 1 von 6) (Englisch)

463800

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite











See the Important Safety and Product Information guide in the product box

for product warnings and other important information.





Always wear safety goggles, ear protection, and a dust mask when drilling,

cutting, or sanding.

Follow these instructions to properly install the all of the components

provided with your echo 100/150/200/300c/500c /550c.



Contact Garmin Product Support if you have any questions while using your

echo. In the USA, go to www.garmin.com/support, or contact Garmin USA

by phone at (913) 397.8200 or (800) 800.1020.

In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.

In Europe, go to www.garmin.com/support and click Contact Support for

in-country support information, or contact Garmin (Europe) Ltd. by phone at

+44 (0) 870.8501241.



• Drill and drill bits

•

in. wrench or socket

• Masking tape

• Number 2 Phillips screwdriver

• Marine sealant

• Hardware for the swivel mount (bolts or screws) (page 3)



Before permanently installing any part of your echo, plan the installation by

determining the location of the various components. Verify that the cables are

long enough to connect the components to each other and to power.



The transducer is the component of your echo that transmits sound waves

through the water and receives them to relay the information to your echo

device. With the supplied hardware, you can install the included transducer

on the transom of your boat (page 1) or on your trolling motor (page 3).

If you already have an existing Garmin 6-pin dual-beam transducer on your

boat, you can use it with your echo device by installing an adapter cable (sold

separately).



The echo device can be mounted using the included swivel-mount bracket

(page 3), or it can be mounted ush with the dashboard using the appropriate

ush-mount kit (sold separately).

When planning a mounting location, choose a location that you can see as

you operate your vessel, provides easy access to the keys on the echo, and is

the appropriate distance from a compass (page 6).



1. Insert the rubber washer

➊

and the plastic spacer

➋

into the transducer

➌

at the same time.

Do not add any lubrication to the rubber washer.

➊

➋

➍

➎

➏

➐

➌

2. Pull the cable back and slide the transducer into the mounting bracket

➍

3. Place a 5 mm at washer

➎

on the 10-32 x 1.75 in. screw

➏

and insert

the screw through the mounting bracket, transducer, spacer, and rubber

washer.

4. Place a 5 mm at washer on the exposed end of the 10-32 x 1.75 in.

screw, and fasten it with the 10-32 lock nut

➐

Do not tighten the 10-32 lock nut. You will adjust the transducer and

tighten the nut after you install the transducer on the boat.





Select a transom-mount location while considering these guidelines for

optimal performance.

• Mount the transducer as close to the center of the boat as possible.

• Do not mount the transducer behind strakes, struts, ttings, water

intake or discharge ports, or anything that creates air bubbles or

causes the water to become turbulent.

The transducer must be in clean (non-turbulent) water for optimal

performance.

• Do not mount the transducer in the path of the propeller on single-

drive boats.

The transducer can cause cavitation that can degrade the performance

of the boat and damage the propeller.

• On twin-drive boats, mount the transducer between the drives, if

possible.

• Do not mount the transducer in a location where it might be jarred

when launching, hauling, or storing.

February, 2011 190-01312-02 Rev. B Printed in Taiwan



 



 

 

 



 

 

 

 

 

 

 

 

 

 

 



 

 

 

 

 

Garmin Echo 100 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Echo 100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info