Bedienungsanleitung Garmin Echo 100 (Seite 5 von 6) (Englisch)

463800

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

echoInstallationInstructions 5



On an echo 200/500c/550c device, the connectors on the cables are keyed to

t only in the correct ports on the cradle. The connected cables are then held

in place by a locking bracket.

No cables connect directly to an echo 200/500c/550c device.

1 Compare the divot

➊

on the cable connector

to the keying on the cradle ports to identify the

correct port.

2. Push the cable connector into the correct port

until it rests rmly in the port.

3. Repeat steps 1 and 2 until all of the

cables are connected to the cradle

➋

4. Place the locking bracket

➌

over the

cables and slide it down to lock them

in place on the cradle.

You will hear an audible click when

the locking bracket is correctly

installed.



After you have connected the cables to the cradle, you can quickly place the

echo device in the cradle without plugging in

any cables.

1. Place the base of the echo

➊

in the

bottom of the cradle

➋

2. Tilt the echo toward the cradle until it

fastens in place.

You will hear an audible click when the

device is secured in the cradle.





After you have connected the cables to the cradle, you can quickly remove

the echo from the cradle without unplugging any

cables.

1. Press the release lever

➊

on the cradle until

the echo device

➋

is released.

2. Tilt the echo device forward and lift it out of

the cradle.



Notice

Do not leave your boat in the water for an extended period of time without

checking for leaks.

Because water is necessary to carry the sonar signal, the transducer must be

in the water to work properly. You cannot get a depth or distance reading

when out of the water. When you place your boat in the water, check for

leaks around any screw holes that were added below the water line.



Notice

When adjusting the depth of the transducer, make the adjustments in

small increments. Placing the transducer too deep can adversely affect the

performance of the boat and put the transducer at risk of striking underwater

objects.

Test the transom mount transducer installation in open water free of

obstacles. Pay attention to your surroundings as you test the transducer.

1. With the boat in the water, turn on the echo device.

2. Drive the boat at a slow speed. If the echo device appears to be working

properly, gradually increase speed while observing the echo device.

If the sonar signal is suddenly lost or the bottom return is severely

degraded, note the speed at which this occurs.

3. Return the boat to the speed at which the signal was lost, and make

moderate turns in both directions while observing the echo device.

4. If the signal strength improves while turning, adjust the transducer so that

it extends another

in. (3 mm) below the transom of the boat.

5. Repeat steps 2–4 until the degradation is eliminated.

6. If the signal does not improve, move the transducer to a different location

on the transom.

➊

➌

➋

➊

➋

➊

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Echo 100 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Echo 100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info