Bedienungsanleitung Garmin Echo 150 (Seite 4 von 6) (Englisch)

463801

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

4 echoInstallationInstructions





1. Feed the cables

➏

through the

in. (16 mm) center hole you drilled

when preparing the swivel-mount base.

2. Place the swivel-mount base

➊

on the

mounting surface, route the cables through

the cable pass-through holes

➎

, and

loosely fasten the swivel-mount base using

the appropriate screws or bolts

➋

3. Place the swivel mount

➌

on the swivel-

mount base, but do not fasten it.

4. Place the echo device or cradle into the

swivel mount (page 4).

5. Pull out enough slack from the power and

transducer cables so that the mount can

fully swivel to the desired positions when

the cables are connected.

6. Remove the echo device or cradle, and the

swivel mount, from the swivel-mount base.

7. Apply marine sealant to the

in. (16 mm)

center hole and to the cable pass-through

holes.

8. Securely fasten the swivel-mount base, using the appropriate screws or

bolts.

9. Place the swivel mount on the swivel-mount base, and fasten it using the

included 10 mm M6×1 Phillips screw

➍





Complete this task only if you do not need to run the

cables through the mounting surface and the mount.

1. Place the swivel-mount base

➊

on the mounting

surface, and fasten it using the appropriate screws

or bolts

➋

2. Place the swivel mount

➌

on the swivel-mount

base, and fasten it using the included 10 mm

M6×1 Phillips screw

➍

3. Seal the cable pass-through holes

➎

with marine

sealant.



1. With the locking arm

➊

in the upward position, place the echo

100/150/300c device

➋

or the echo 200/500c/550c cradle

➌

into the

swivel mount

➍

➊

➌

➍ ➍

➋

2. Tilt the mount for the desired viewing angle and press down on the

locking arm.





1. Route the power cable from the swivel mount to the boat battery or fuse

block.

• If necessary, extend the wires using 20 AWG or larger wire.

• If you connect the power cable to the fuse block, rst remove the

inline fuse holder on the red wire.

2. Connect the red wire to the positive terminal on the battery or fuse block,

and connect the black wire to the negative terminal.



On an echo 100/150/300c device, the connectors on the cables are keyed to

t only in the correct ports on the device.

1. Compare the divot

➊

on the cable connector to the

keying on the device ports to identify the correct port.

2. Push the cable connector into the correct port until the

connector is fully seated.

3. Repeat steps 1 and 2 until all of the cables are connected

to the device.

➏

➎

➌

➍

➋

➊

➎

➌

➍

➋

➊

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Echo 150 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Echo 150

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info