Bedienungsanleitung Garmin echoMAP 70 (Seite 24 von 44) (Englisch)

522317

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Radar Display Modes

NOTE: Not all modes are available with all radar devices and all

chartplotters.

Select Radar, and select a mode.

Cruising Mode: Shows a full-screen image of the gathered

radar information.

Harbor Mode: Intended for use in inland waters, this mode

works best with short-range signals (2 nm or less).

Offshore Mode: Intended for use in open waters, this mode

works best with long-range signals.

Sentry Mode: Allows you to put the radar into timed-transmit

mode, in which you can configure a radar transmit and

standby cycle to conserve power. You can also enable a

guard zone in this mode, which identifies a safe zone around

your boat. If you switch from Sentry mode to another mode,

the radar switches to full-time transmission and disables all

guard zones.

Radar Overlay Mode: Shows a full-screen image of the

gathered radar information on top of the Navigation chart.

The Radar overlay displays data based on the most recently

used radar mode.

Transmitting Radar Signals

NOTE: As a safety feature, the radar enters standby mode after

it warms up. This gives you an opportunity to verify the area

around the radar is clear before beginning radar transmission.

1With the chartplotter off, connect your radar as described in

the radar installation instructions.

2Turn on the chartplotter.

The radar warms up and a countdown alerts you when the

radar is ready.

3Select Radar.

4Select a radar mode.

A countdown message appears while the radar is starting up.

5Select Menu > Transmit Radar.

Range of Radar Signals

The range of the radar signal indicates the length of the pulsed

signal transmitted and received by the radar. As the range

increases, the radar transmits longer pulses in order to reach

distant targets. Closer targets, especially rain and waves, also

reflect the longer pulses, which can add noise to the Radar

screen. Viewing information about longer-range targets can also

decrease the amount of space available on the Radar screen

for viewing information about shorter-range targets.

Tips for Selecting a Radar Range

• Determine what information you need to see on the Radar

screen.

For example, do you need information about nearby weather

conditions or targets and traffic, or are you more concerned

about distant weather conditions?

• Assess the environmental conditions where the radar is

being used.

Especially in inclement weather, longer-range radar signals

can increase the clutter on the Radar screen and make it

more difficult to view information about shorter-range targets.

In rain, shorter-range radar signals can enable you to view

information about nearby objects more effectively, if the rain

clutter setting is configured optimally.

• Select the shortest effective range, given your reason for

using radar and the present environmental conditions.

Adjusting the Zoom Scale on the Radar

Screen

The radar zoom scale, also called the radar signal range,

represents the distance from your position (the center) to the

outermost ring.

From a Radar screen, select or .

Each ring represents an even division of the zoom scale.

For example, if the zoom scale is set at 3 miles, each ring

represents 1 mile from the center out.

Sentry Mode

Sentry mode allows you to put the radar into timed-transmit

mode, in which you can configure a radar transmit and standby

cycle to conserve power. You can also enable a guard zone in

this mode, which identifies a safe zone around your boat and

sounds an alarm when a radar object enters the zone. Sentry

mode works with all Garmin GMR model radars.

Enabling Timed Transmit

From the sentry screen, select Menu > Sentry Setup >

Timed Transmit > On.

Setting the Standby and Transmit Times

Before you can set the standby and transmit times, you must

enable timed transmit (Enabling Timed Transmit).

To help conserve power, you can indicate the radar standby

time and the transmit time to implement periodic radar signal

transmissions at set intervals.

1From the sentry screen, select Menu > Sentry Setup.

2Select Stdby Time.

3Enter the time interval between radar signal transmissions.

4Select Transmit Time.

5Enter the duration of each radar signal transmission.

Enabling a Guard Zone

From the sentry screen, select Menu > Sentry Setup >

Enable Guard Zone.

Defining a Circular Guard Zone

Before you can define the boundaries of the guard zone, you

must enable a guard zone (Enabling a Guard Zone).

You can define a circular guard zone that completely

encompasses your boat.

1From the sentry screen, select Menu > Sentry Setup >

Adjust Guard Zone > Move Radar Guard Zone > Circle.

2Select the location of the outer guard zone circle.

3Select the location of the inner guard zone circle to define

the width of the guard zone.

Defining a Partial Guard Zone

You can define the boundaries of a guard zone that does not

completely encompass your boat.

1From the sentry screen, select Menu > Sentry Setup >

Adjust Guard Zone > Move Radar Guard Zone > Corner

2Touch and drag the location of the outer guard-zone corner

À.

18 Radar

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin echoMAP 70 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin echoMAP 70

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info