Bedienungsanleitung Garmin echoMAP 70 (Seite 28 von 44) (Englisch)

522317

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

When an engine alarms is triggered, a gauge status alarm

message appears and the gauge may become red depending

on the type of alarm.

Enabling Some Engine Gauge Status Alarms

1From the engine gauges screen, select Menu > Gauge

Setup > Status Alarms > Custom.

2Select one or more engine gauge alarms to turn on or off.

Selecting the Number of Engines Shown in Gauges

You can show information for up to four engines.

1From the engine gauges screen, select Menu > Gauge

Setup > Engine Selection > Num. Engines.

2Select an option:

• Select the number of engines.

• Select Auto Configure to automatically detect the

number of engines.

Customizing the Engines Shown in Gauges

Before you can customize how the engines are shown in the

gauges, you must manually select the number of engines

(Selecting the Number of Engines Shown in Gauges).

1From the engine gauges screen, select Menu > Gauge

Setup > Engine Selection > Edit Engines.

2Select First Engine.

3Select the engine to display in the first gauge.

4Repeat for the remaining engine bars.

Configuring the Fuel Gauges Display

Before you can configure and display the fuel levels, you must

connect a compatible engine, fuel flow sensor, or tank level

sensor to the NMEA 2000 network.

You can display the total amount of fuel on-board either as a

numeric display that shows the total fuel or as a graphic display

that shows the level in each fuel tank.

1Select Gauges > Engine > Menu > Gauge Setup > Fuel

Display.

2Select an option:

• To display the total fuel level in all tanks, select Use Total

Fuel Onboard.

• To display the amount of fuel in each tank, select Use

Fuel Tank Levels.

Setting the Fuel Capacity of the Vessel

1Select Settings > My Vessel > Fuel Capacity.

2Enter the combined total capacity of the fuel tanks.

Synchronizing the Fuel Data with the Actual Vessel

Fuel

You can synchronize the fuel levels in the chartplotter with the

actual fuel in the vessel when you add fuel to your vessel.

1Select Gauges > Engine > Menu.

2Select an option:

• After you have filled up all the fuel tanks on the vessel,

select Fill Up All Tanks. The fuel level is reset to

maximum capacity.

• After you have added less than a full tank of fuel, select

Add Fuel to Boat, and enter the amount added.

• To specify the total fuel in the vessel tanks, select Set

Total Fuel Onboard, and enter the total amount of fuel in

the tanks.

Setting the Fuel Alarm

Before you can set a fuel level alarm, a compatible fuel flow

sensor must be connected to the NMEA 2000 network.

You can set an alarm to sound when the total amount of

remaining onboard fuel reaches the level you specify.

1Select Settings > Alarms > Fuel > Fuel Alarm > On.

2Enter the remaining amount of fuel that triggers the alarm.

Viewing the Wind Gauges

Before you can view wind information, you must have a wind

sensor connected to the chartplotter.

Select Gauges > Wind.

Configuring the Sailing Wind Gauge

You can configure the sailing wind gauge to show true or

apparent wind speed and angle.

1From the wind gauge, select Menu > Sailing Wind Gauge.

2Select an option:

• To show true or apparent wind angle, select Needle, and

select an option.

• To show true or apparent wind speed, select Wind

Speed, and select an option.

Configuring the Speed Source

You can specify whether the vessel speed data displayed on

the gauge and used for wind calculations is based on water

speed or GPS speed.

1From the wind gauge, select Menu > Compass Gauge >

Speed Display.

2Select an option:

• To calculate the vessel speed based on data from the

water-speed sensor, select Water Speed.

• To calculate the vessel speed based on GPS data, select

GPS Speed.

Configuring the Heading Source of the Wind Gauge

You can specify the source of the heading displayed on the

wind gauge. Magnetic heading is the heading data received

from a heading sensor, and GPS heading is calculated by your

chartplotter GPS (course over ground).

1From the wind gauge, select Menu > Compass Gauge >

Heading Source.

2Select GPS Hdg or Magnetic.

NOTE: When moving at low speeds or when stationary, the

magnetic compass source is more accurate than the GPS

source.

Customizing the Close-Hauled Wind Gauge

You can specify the range of the close-hauled wind gauge for

both the upwind scale and the downwind scale.

1From the wind gauge, select Menu > Compass Gauge >

Set Gauge Type > Close Hauled Gauge.

2Select an option:

• To set the maximum and minimum values that appear

when the upwind close-hauled wind gauge appears,

select Change Upwind Scale, and set the angles.

• To set the maximum and minimum values that appear

when the downwind close-hauled wind gauge appears,

select Change Downwind Scale, and set the angles.

• To view true or apparent wind, select Wind, and select an

option.

Viewing the Environment Gauges

Select Gauges > Environment.

Configuring the Alignment of the Wind Gauge

You can specify the alignment of the wind gauge on the

environment gauges.

1Select Gauges > Environment > Menu > Alignment.

22 Gauges and Almanac Information

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin echoMAP 70 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin echoMAP 70

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info