Bedienungsanleitung Garmin echoMAP CHIRP 72 (Seite 24 von 44) (Englisch)

657704

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

RealVü 3D Down Sonar View

This sonar view shows a three-dimensional view of what is

below the transducer and can be used when you are stationary

and want to see what is around your boat.

RealVü 3D Historical Sonar View

This sonar view provides a three-dimensional view of what is

behind your boat as you are moving and shows the entire water

column in 3D, from the bottom to the top of the water. This view

is used for finding fish.

Color legend

Boat

Range

Bottom

Structure

Fish

FrontVü Sonar View

The Panoptix FrontVü sonar view increases your situational

awareness by showing obstructions under the water, up to

91 meters (300 feet) in front of the boat.

The ability to effectively avoid forward collisions with FrontVü

sonar decreases as your speed rises above 8 knots.

To see the FrontVü sonar view, you must install and connect a

compatible transducer, such as a PS21 transducer. You may

need to update the transducer software.

Changing the Sonar View

From a combination screen with sonar, select MENU > Edit

Combination.

Select the window to change.

Select a sonar view.

Selecting the Transducer Type

Before you can select the transducer type, you must know what

kind of transducer you have.

This chartplotter is compatible with the Garmin ClearVü

™

transducer as well as a range of accessory transducers

including Garmin GT transducers, which are available at

www.garmin.com.

If you are connecting a transducer that was not included with the

chartplotter, you may need to set the transducer type to make

the sonar function properly. If the device automatically detected

your transducer, this option does not appear.

From a sonar view, select MENU > Sonar Setup >

Installation > Transducer Type.

Select an option:

• If you have a 200/77 kHz, dual-beam transducer, select

Dual Beam (200/77 kHz).

• If you have a 200/50 kHz, dual-frequency transducer,

select Dual Frequency (200/50 kHz).

• If you have another type of transducer, select it from the

list.

Calibrating the Compass

Before you can calibrate the compass, the transducer must be

installed on the shaft far enough away from the trolling motor to

avoid magnetic interference, and deployed in the water.

Calibration must be of sufficient quality to enable the internal

compass.

NOTE: To use the compass, you must mount the transducer on

the shaft. The compass does not work when you mount the

transducer on the motor.

NOTE: Compass calibration is available only for transducers

with an internal compass.

You can begin turning your boat before calibrating, but you must

fully rotate your boat 1.5 times during calibration.

From a ForwardVü or LiveVü Forward sonar page, select

MENU > Sonar Setup > Installation.

If necessary, select Use AHRS.

Select Calibrate Compass.

Follow the on-screen instructions.

Creating a Waypoint on the Sonar Screen

From a sonar view, select Pause Sonar.

Select a location.

Select or .

If necessary, edit the waypoint information.

Measuring Distance on the Sonar Screen

You can measure the distance between two points on the

SideVü sonar view.

From the SideVü sonar view, select a location on the screen.

Select .

A push pin appears on the screen at the selected location.

Select another location.

The distance and angle from the pin is listed in the upper-left

corner.

TIP: To reset the pin and measure from the current location of

the pin, select .

Pausing the Sonar Display

From a sonar view, select MENU > Pause Sonar.

Viewing Sonar History

You can scroll the sonar display to view historical sonar data.

NOTE: Not all transducers save historical sonar data.

From a sonar view, select MENU > Pause Sonar.

Use the arrow keys.

Adjusting the Level of Detail

You can control the level of detail and noise shown on the sonar

screen either by adjusting the gain for traditional transducers or

by adjusting the brightness for Garmin ClearVü transducers.

If you want to see the highest intensity signal returns on the

screen, you can lower the gain or brightness to remove lower

intensity returns and noise. If you want to see all return

information, you can increase the gain or brightness to see more

information on the screen. This also increases noise, and can

make it more difficult to recognize actual returns.

18 Sonar

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin echoMAP CHIRP 72 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin echoMAP CHIRP 72

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info