Bedienungsanleitung Garmin Echomap UHD (Seite 2 von 6) (Englisch)

737433

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

Bail Mounting a Device with a Swivel Base

NOTICE

Only pan-head machine bolts or self-tapping screws should be

used to secure the swivel base. If you use screws with

countersunk heads, you may damage the mounting bracket.

Some models have the option of adding a swivel base to the bail

mount, so you can turn the device for a wider range of viewing

angles.

NOTE: The ECHOMAP UHD 9x models do not have a swivel

option.

Using the swivel base as a template, mark three pilot

holes .

Using a 3 mm (

in.) drill bit, drill the three pilot holes.

Using the included wood screws , secure the swivel base

to the mounting surface.

Place the bail-mount bracket on the swivel base, and

secure it using the swivel-mount knob .

Install the bail-mount knobs on the sides of the cradle.

Place the device in the bail-mount bracket and tighten the

bail-mount knobs.

Connect each cable to a port on the cradle, using the locking

bracket or locking rings to secure the cables to the cradle

(Connection Considerations, page 2).

Flush Mounting the Device

NOTICE

Be careful when cutting the hole to flush mount the device.

There is only a small amount of clearance between the case and

the mounting holes, and cutting the hole too large could

compromise the stability of the device after it is mounted.

Using a metal pry tool such as a screwdriver can damage the

trim caps and the device. Use a plastic pry tool when possible.

You can mount the device in your dashboard using the flush-

mount template and appropriate hardware.

Trim the template and make sure it fits in the location where

you want to mount the device.

Secure the template to the mounting location.

Using a 9.5 mm (

in.) drill bit, drill one or more of the holes

inside the corners of the solid line on the template to prepare

the mounting surface for cutting.

Using a jigsaw or rotary cutting tool, cut the mounting surface

along the inside of the solid line indicated on the template.

Place the device into the cutout to test the fit.

If necessary, use a file and sandpaper to refine the size of

the hole.

If your device has trim caps, use a pry tool, such as a flat

piece of plastic or a screwdriver, to carefully pry up the

corners of the trim caps , slide the pry tool to the center ,

and remove the trim caps.

Ensure the mounting holes on the device line up with the pilot

holes on the template.

If the mounting holes on the device do not line up with the

pilot holes on the template, mark the new pilot-hole locations

on your template.

Using a 3 mm (

in.) drill bit, drill the pilot holes.

Remove the template from the mounting surface.

Place the device in the cradle.

NOTE: You must use the cradle and locking bracket or

locking rings when you flush-mount the device.

If you will not have access to the back of the device after you

mount it, connect all necessary cables to the cradle and

secure the cables with the locking bracket or locking rings

before placing the device into the cutout (Connection

Considerations, page 2).

To prevent corrosion of the metal contacts, cover unused

connectors with weather caps.

Install the rubber gasket pieces on the back of the device.

The pieces of the rubber gasket have adhesive on the back.

Make sure you remove the protective liner before installing

them on the device.

Connect each cable to a port on the cradle, using the locking

bracket or locking rings to secure the cables to the cradle

(Connection Considerations, page 2).

Place the device and cradle into the cutout.

Secure the device to the mounting surface using the included

screws.

Install the trim caps by snapping them in place around the

edges of the device.

Connection Considerations

After connecting the cables to the cradle, tighten the locking

rings to secure each cable.

Connecting the Cables to the ECHOMAP UHD 6x

Cradle

The connectors on the cables are keyed to fit only in the correct

ports on the ECHOMAP UHD 6x cradle. The connected cables

are held in place by a locking bracket.

Slide the cable locking bracket up from the bottom, and

remove the bracket from the cradle.

Compare the divots on each cable connector to the keying

on each port to determine which cable corresponds to each

port.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Echomap UHD Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Echomap UHD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info