Bedienungsanleitung Garmin Echomap UHD (Seite 47 von 52) (Englisch)

737433

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Read and agree to the terms.

If you are on a Mac computer, select Go to Mac download

page.

Select Download.

If necessary, choose a location, and select Save.

Double-click the downloaded file.

If you are on a computer running Windows software, select

Next, select the drive associated with the memory card, and

select Next > Finish.

A Garmin folder containing the software update is created on

the memory card. The software update can take several

minutes to load onto the memory card.

If you are on a Mac computer, copy the Garmin folder to the

root directory of the memory card.

The software update can take several minutes to load onto

the memory card.

After loading the update onto the memory card, install the

software on the chartplotter (Updating the Device Software,

page 41).

Updating the Device Software

Before you can update the software, you must obtain a

software-update memory card or load the latest software onto a

memory card (Loading the New Software on a Memory Card,

page 40).

Turn on the chartplotter.

After the home screen appears, insert the memory card into

the card slot.

NOTE: In order for the software update instructions to

appear, the device must be fully booted before the card is

inserted.

Follow the on-screen instructions.

Wait several minutes while the software update process

completes.

When prompted, leave the memory card in place and restart

the chartplotter manually.

Remove the memory card.

NOTE: If the memory card is removed before the device

restarts fully, the software update is not complete.

Cleaning the Screen

NOTICE

Cleaners containing ammonia will harm the anti-reflective

coating.

The device is coated with a special anti-reflective coating which

is very sensitive to waxes and abrasive cleaners.

Apply an eyeglass lens cleaner specified as safe for anti-

reflective coatings to the cloth.

Gently wipe the screen with a soft, clean, lint-free cloth.

Screenshots

You can capture a screenshot of any screen shown on your

chartplotter as a .png file. You can transfer the screenshot to

your computer.

Capturing Screenshots

Insert a memory card into the card slot.

Select Settings > System > Display > Screenshot Capture

> On.

Go to a screen you want to capture.

Hold HOME for at least six seconds.

Copying Screenshots to a Computer

Remove the memory card from the chartplotter, and insert it

into a card reader that is attached to a computer.

From Windows Explorer, open the Garmin\scrn folder on the

memory card.

Copy a .bmp file from the card and paste it to any location on

the computer.

Troubleshooting

My device will not acquire GPS signals

If the device is not acquiring satellite signals, there could be a

few causes. If the device has moved a large distance since the

last time it has acquired satellites or has been turned off for

longer than a few weeks or months, the device may not be able

to acquire the satellites correctly.

• Ensure the device is using the latest software. If not, update

the device software (Updating the Device Software, page 41).

• Make sure the device has a clear view of the sky so the

antenna can receive the GPS signal. If it is mounted inside of

a cabin, it should be close to a window so it can receive the

GPS signal.

My device will not turn on or keeps turning off

Devices erratically turning off or not turning on could indicate an

issue with the power supplied to the device. Check these items

to attempt to troubleshoot the cause of the power issue.

• Make sure the power source is generating power.

You can check this several ways. For example, you can

check whether other devices powered by the source are

functioning.

• Check the fuse in the power cable.

The fuse should be located in a holder that is part of the red

wire of the power cable. Check that the proper size fuse is

installed. Refer to the label on the cable or the installation

instructions for the exact fuse size needed. Check the fuse to

make sure there is still a connection inside of the fuse. You

can test the fuse using a multimeter. If the fuse is good, the

multimeter reads 0 ohm.

• Check to make sure the device is receiving at least 12 V.

To check the voltage, measure the female power and ground

sockets of the power cable for DC voltage. If the voltage is

less than 12 V, the device will not turn on.

• If the device is receiving enough power but does not turn on,

contact Garmin product support.

Changing the Fuse in the Power Cable

Open the fuse housing .

Twist and pull the fuse to remove it .

Insert a new fast-blow fuse.

Close the fuse housing.

My sonar does not work

• Push the transducer cable all the way into the back of the

device.

Even if the cable seems to be connected, you should push

firmly so that it is fully seated.

• Press , and ensure sonar is enabled.

• Select the correct transducer type (Selecting the Transducer

Type, page 22).

Appendix 41

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Echomap UHD Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Echomap UHD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info