Bedienungsanleitung Garmin ECHOMAP Ultra serie (Seite 34 von 52) (Englisch)

691420

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

When the autopilot is in standby mode, select Wind Hold.

Engaging Wind Hold from Heading Hold

Before you can enable the wind hold type, you must connect a

NMEA 2000 or NMEA 0183 wind sensor to the autopilot.

With heading hold engaged, select Menu > Wind Hold.

Adjusting the Wind Hold Angle with the Autopilot

You can adjust the wind hold angle on the autopilot when wind

hold is engaged.

• To adjust the wind hold angle in increments of 1°, select or

• To adjust the wind hold angle in increments of 10°, hold or

Tack and Gybe

You can set the autopilot to perform a tack or gybe while

heading hold or wind hold is engaged.

Tacking and Gybing from Heading Hold

Engage heading hold (Engaging the Autopilot, page 25).

Select Menu.

Select an option.

The autopilot steers your boat through a tack or gybe.

Tacking and Gybing from Wind Hold

Before you can engage wind hold, you must have a wind sensor

installed.

Engage wind hold (Engaging Wind Hold, page 27).

Select Menu.

Select an option.

The autopilot steers your boat through a tack or gybe, and

information about the progress of the tack or gybe appears

on the screen.

Setting a Tack and Gybe Delay

The tack and gybe delay allows you to delay steering a tack and

gybe after you initiate the maneuver.

From the autopilot screen, select Menu > Autopilot Setup >

Sailing Setup > Tack/Gybe Delay.

Select the length of the delay.

If necessary, select Done.

Enabling the Gybe Inhibitor

NOTE: The gybe inhibitor does not prevent you from manually

performing a gybe using the helm or step steering.

The gybe inhibitor prevents the autopilot from performing a

gybe.

From the autopilot screen, select Menu > Autopilot Setup >

Sailing Setup > Gybe Inhibitor.

Select Enabled.

Force

™

Trolling Motor Control

WARNING

Do not run the motor when the propeller is out of the water.

Contact with the rotating propeller may result in severe injury.

Do not use the motor in areas where you or other people in the

water may come into contact with the rotating propeller.

Always disconnect the motor from the battery before cleaning or

servicing the propeller to avoid injury.

You are responsible for the safe and prudent operation of your

vessel. The autopilot is a tool that enhances your capability to

operate your boat. It does not relieve you of the responsibility of

safely operating your boat. Avoid navigational hazards and

never leave the helm unattended.

Learn to operate the autopilot on calm and hazard-free open

water.

Use caution when operating the autopilot near hazards in the

water, such as docks, pilings, and other boats.

CAUTION

When using the autopilot features, be prepared for sudden

stops, acceleration, and turns.

When stowing or deploying the motor, be aware of the risk of

entrapment or pinching from moving parts, which can result in

injury.

When stowing or deploying the motor, be aware of slick surfaces

around the motor. Slipping when stowing or deploying the motor

may result in injury.

You can connect the Force trolling motor to the chartplotter to

view and control the motor using the chartplotter.

Connecting to a Trolling Motor

You can connect the chartplotter wirelessly to a compatible

Garmin Force trolling motor on your boat to control the trolling

motor from the chartplotter

Turn on the chartplotter and the trolling motor.

Enable the Wi‑Fi network on the chartplotter (Setting Up the

‑

Fi Wireless Network, page 37).

Make sure that this chartplotter is the host of the network.

On the chartplotter, select Settings > Communications >

Wireless Devices > Garmin Trolling Motor.

On the trolling motor display panel, press three times to

enter pairing mode.

on the trolling motor display panel is solid blue as it

searches for a connection to the chartplotter, and turns green

when the connection is successful.

After the chartplotter and trolling motor connect successfully,

enable the trolling motor overlay bar to control the motor (Adding

the Trolling Motor Controls to Screens, page 28).

Adding the Trolling Motor Controls to

Screens

After you have connected the chartplotter to the Force trolling

motor, you must add the trolling motor control bar to screens to

control the trolling motor.

Open a screen from which you would like to control the

trolling motor.

Select an option:

• From a combination page or SmartMode

™

layout, select

Menu > Edit > Overlay Numbers.

• From a full screen, select Menu > xxx.

Select Top Bar or Bottom Bar.

Select Trolling Motor Bar.

Repeat these steps to add the trolling motor controls to all of the

screens from which you would like to control the trolling motor.

Trolling Motor Control Bar

The trolling motor control bar allows you to control a Force

trolling motor and see the status of the motor.

Select an item to engage it. The button illuminates when

selected. Select the item again to disengage it.

Trolling motor battery status.

Turns the propeller on and off.

Reduces the speed.

28 Force

™

Trolling Motor Control

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin ECHOMAP Ultra serie Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin ECHOMAP Ultra serie

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info