Bedienungsanleitung Garmin Fenix 2 (Seite 16 von 26) (Englisch)

589540

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Alert Name Alert Type Description

Distance Event,

recurring

You can set an interval, a custom distance

from your final destination, or a custom

distance if you go off-course from a track

or route.

Elevation Event, range,

recurring

You can set minimum and maximum

elevation values. You can also set the

device to alert you when you ascend or

descend a specified amount.

Heart Rate Range You can set minimum and maximum heart

rate values or select zone changes. See

About Heart Rate Zones and Heart Rate

Zone Calculations.

Nav. Arrival Event You can set alerts for reaching waypoints

and the final destination of a track or route.

Pace Range You can set minimum and maximum pace

values.

Power Range You can set the high or low power level.

Proximity Recurring See Setting a Proximity Alarm.

Speed Range You can set minimum and maximum

speed values.

Time Event,

recurring

You can set an interval, a custom time

until sunset, or a custom time from your

estimated time of arrival.

Setting an Alert

Hold MENU.

Select Settings > Activity.

Select an activity.

NOTE: This feature is not available for all activities.

Select Alerts.

Select the alert name.

If necessary, select the type of alert.

Select a zone, enter the minimum and maximum values, or

enter a custom value for the alert.

If necessary, turn on the alert.

For event and recurring alerts, a message appears each time

you reach the alert value. For range alerts, a message appears

each time you exceed or drop below the specified range

(minimum and maximum values).

Setting a Proximity Alarm

Proximity alarms alert you when you are within a specified

range of a particular location.

Hold MENU.

Select Settings > Activity.

Select an activity.

NOTE: This feature is not available for all activities.

Select Alerts > Proximity > Edit > Create New.

Select a location.

Enter a radius.

Select Done.

Using Auto Pause

You can use Auto Pause to pause the timer automatically when

you stop moving. This feature is helpful if your activity includes

stop lights or other places where you need to or stop.

NOTE: History is not recorded while the timer is stopped or

paused.

Hold MENU.

Select Settings > Activity.

Select an activity.

NOTE: This feature is not available for all activities.

Select Auto Pause.

Auto Lap

Marking Laps by Distance

You can use Auto Lap to mark a lap at a specific distance

automatically. This feature is helpful for comparing your

performance over different parts of an activity (for example,

every 1 mile or 5 kilometers).

Hold MENU.

Select Settings > Activity.

Select an activity.

NOTE: This feature is not available for all activities.

Select Auto Lap.

Select a distance.

Each time you complete a lap, a message appears that displays

the time for that lap. The device also beeps or vibrates if audible

tones are turned on (General Settings).

If necessary, you can customize the data pages to display

additional lap data (Customizing the Data Pages).

UltraTrac

The UltraTrac feature is a GPS setting that records track points

and sensor data less frequently. Enabling the UltraTrac feature

increases battery life but decreases the quality of recorded

activities. You should use the UltraTrac feature for activities that

demand longer battery life and for which frequent sensor data

updates are less important. The default interval between track

points is one point per minute. You can adjust the interval.

3D Speed and Distance

You can set 3D speed and distance to calculate your speed or

distance using both your elevation change and your horizontal

movement over ground. You can use it during activities such as

skiing, climbing, navigating, hiking, running, or biking.

Sensors Settings

• You can calibrate and configure the internal compass

(Compass Settings).

• You can calibrate and configure the internal barometric

altimeter (Altimeter Settings).

• You can pair and configure ANT+ sensors (ANT+ Sensors).

Compass Settings

Hold MENU, and select Settings > Sensors > Compass.

Display: Sets the directional heading on the compass to

degrees or milli-radians.

North Ref.: Sets the north reference of the compass (Setting

the North Reference).

Mode: Sets the compass to use either a combination of GPS

and the electronic sensor data when moving (Auto) or GPS

data only (Off).

Calibrate: Allows you to manually calibrate the compass sensor

(Calibrating the Compass).

Setting the North Reference

You can set the directional reference used in calculating

heading information.

Hold MENU.

Select Settings > Sensors > Compass > North Ref..

Select an option:

• To set geographic north as the heading reference, select

True.

• To set the magnetic declination for your location

automatically, select Magnetic.

• To set grid north (000º) as the heading reference, select

Grid.

12 Customizing Your Device

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Fenix 2 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Fenix 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info