Bedienungsanleitung Garmin Fenix 3 (Seite 21 von 28) (Englisch)

589541

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

The Garmin logos should be right-side up.

4Bring the device within 3 m (10 ft.) of the heart rate monitor.

After you put on the heart rate monitor, it is active and sending

data.

TIP: If the heart rate data is erratic or does not appear, see the

troubleshooting tips (Tips for Erratic Heart Rate Data).

Tips for Erratic Heart Rate Data

If the heart rate data is erratic or does not appear, you can try

these tips.

• Reapply water to the electrodes and contact patches.

• Tighten the strap on your chest.

• Warm up for 5–10 minutes.

• Follow the care instructions (Caring for the Heart Rate

Monitor).

• Wear a cotton shirt or thoroughly wet both sides of the strap.

Synthetic fabrics that rub or flap against the heart rate

monitor can create static electricity that interferes with heart

rate signals.

• Move away from sources that can interfere with your heart

rate monitor.

Sources of interference may include strong electromagnetic

fields, some 2.4 GHz wireless sensors, high-voltage power

lines, electric motors, ovens, microwave ovens, 2.4 GHz

cordless phones, and wireless LAN access points.

Using an Optional Bike Cadence Sensor

You can use a compatible bike cadence sensor to send data to

your device.

• Pair the sensor with your device (Pairing ANT+ Sensors).

• Update your fitness user profile information (Setting Up Your

User Profile).

• Go for a ride (Going for a Ride).

Foot Pod

Your device is compatible with the foot pod. You can use the

foot pod to record pace and distance instead of using GPS when

you are training indoors or when your GPS signal is weak. The

foot pod is on standby and ready to send data (like the heart

rate monitor).

After 30 minutes of inactivity, the foot pod powers off to

conserve the battery. When the battery is low, a message

appears on your device. Approximately five hours of battery life

remain.

Foot Pod Calibration

The foot pod is self-calibrating. The accuracy of the speed and

distance data improves after a few outdoor runs using GPS.

Calibrating Your Foot Pod Manually

Before you can calibrate your device, you must pair your device

with the foot pod (Pairing ANT+ Sensors).

Manual calibration is recommended if you know your calibration

factor. If you have calibrated a foot pod with another Garmin

product, you may know your calibration factor.

1Hold UP.

2Select Settings > Sensors > Foot Pod > Cal. Factor.

3Adjust the calibration factor:

• Increase the calibration factor if your distance is too low.

• Decrease the calibration factor if your distance is too high.

tempe

The tempe is an ANT+ wireless temperature sensor. You can

attach the sensor to a secure strap or loop where it is exposed

to ambient air, and therefore, provides a consistent source of

accurate temperature data. You must pair the tempe with your

device to display temperature data from the tempe.

Device Information

Viewing Device Information

You can view the unit ID, software version, and license

agreement.

1Hold UP.

2Select Settings > System > About.

Device Care

NOTICE

Do not use a sharp object to clean the device.

Avoid chemical cleaners, solvents, and insect repellents that can

damage plastic components and finishes.

Thoroughly rinse the device with fresh water after exposure to

chlorine, salt water, sunscreen, cosmetics, alcohol, or other

harsh chemicals. Prolonged exposure to these substances can

damage the case.

Avoid pressing the keys under water.

Avoid extreme shock and harsh treatment, because it can

degrade the life of the product.

Do not store the device where prolonged exposure to extreme

temperatures can occur, because it can cause permanent

damage.

Cleaning the Device

NOTICE

Even small amounts of sweat or moisture can cause corrosion

of the electrical contacts when connected to a charger.

Corrosion can prevent charging and data transfer.

1Wipe the device using a cloth dampened with a mild

detergent solution.

2Wipe it dry.

After cleaning, allow the device to dry completely.

Metal Watch Band Adjustment

If your watch includes a metal watch band, you should take your

watch to a jeweler or other professional to adjust the length of

the metal band.

Specifications

Battery type Rechargeable, built-in lithium-ion battery

Battery life Up to 6 wk.

Water rating 10 ATM*

Operating temperature range From -20º to 55ºC (from -4º to 131ºF)

Charging temperature range From 0º to 45ºC (from 32º to 113ºF)

Radio frequency/protocol 2.4 GHz ANT+ wireless technology

Bluetooth Smart device

*The device withstands pressure equivalent to a depth of 100 m.

For more information, go to www.garmin.com/waterrating.

Battery Information

The actual battery life depends on the features enabled on your

device, such as activity tracking, smartphone notifications, GPS,

internal sensors, and connected ANT+ sensors.

Battery Life Mode

Up to 20 hr. Normal GPS mode

Up to 50 hr. UltraTrac GPS mode with two-minute polling interval

Up to 6 wk. Watch mode

Device Information 17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Fenix 3 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Fenix 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info