Bedienungsanleitung Garmin Fishfinder 400C (Seite 13 von 40) (Englisch)

38896

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Fishnder 400C Owner’s Manual 

InstallIng the FIshFInder 400c

When selecting a transom mount location, consider the following for

optimal performance:

• For your sonar to operate properly, the transducer must be

located in calm water. DO NOT mount the transducer behind

strakes, rivet lines, struts, ttings, water intake, discharge

ports, eroding paint, or anything that creates turbulence.

• Mount the transducer as close to the center of the boat as

possible.

• DO NOT cut the transducer lead. (This voids your warranty.)

• DO NOT mount the transducer in locations where it might be

jarred when launching, hauling, trailering, or storing.

• DO NOT mount the transducer in the path of the prop on

single-drive boats. The transducer can cause cavitation that

can degrade the boat’s performance and damage the prop. On

twin-drive boats, mount the transducer between the drives, if

possible.

NOTE: DO NOT mount the transducer behind strakes, struts,

ttings, water intake or discharge ports, or anything that creates

air bubbles or causes the water to become turbulent. The

transducer must be in clean (non-turbulent) water for optimal

performance.

Tool List (not included)—drill, 3/8" wrench or socket, 5/32" and

1/8" drill bits, masking tape, #2 Phillips screwdriver, and marine

sealant.

To mount the transducer on a transom:

1. Positionthetransducermountattheselectedtransom

location.Makesurethetransducerisparallelwiththewater

line.Markthecenterlocationsofeachholeonthetransducer

mount.

2. Usinga5/32"bit,drillthepilotholesapproximately1"

(25mm)deepatthemarkedlocations.Toavoiddrillingthe

holestoodeep,wrapapieceoftapearoundthebitat1"from

thepointofthebit.

3. Applymarinesealanttothe5x30mmscrews.Attachthe

transducerassemblytothetransomusingthe5x30mm

screws.Adjustthetransducerassemblytoextendbeyond

thebottomofthetransomapproximately1/8"(3mm)on

berglasshullsor3/8"(10mm)onaluminumhulls.Adjustthe

transducerassemblytobealignedparallelwiththewater.

4. Tightenthe10-32lockingnutuntilittouchesthemounting

bracket,andthentighten1/4turnmore.(Donotovertighten.)

5. Placetherstcableclamponthetransducercable

approximatelyonethirdofthedistancebetweenthe

transducerandthetopofthetransom.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Fishfinder 400C Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Fishfinder 400C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info