Bedienungsanleitung Garmin Fleet 670V (Seite 20 von 24) (Englisch)

674201

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

If using a dampened cloth, turn off the device and disconnect

the device from power.

Gently wipe the screen with the cloth.

Avoiding Theft

• Remove the device and mount from sight when not in use.

• Remove the residue left on the windshield by the suction cup.

• Do not keep your unit in the glove compartment.

• Register your device at http://my.garmin.com.

Removing the Device, Mount, and Suction

Cup

Removing the Device from the Mount

Grip the device by the top and bottom.

Pull the bottom edge of the device toward you until it releases

from the magnet.

Pulling the device straight toward you may cause the mount

to release from the suction cup.

Removing the Mount from the Suction Cup

Turn the device mount to the right or left.

Apply pressure until the socket on the mount releases the

ball on the suction cup.

Removing the Suction Cup from the Windshield

Flip the lever on the suction cup toward you.

Pull the tab on the suction cup toward you.

Purchasing Additional Maps

Go to your device product page at (www.garmin.com).

Click the

Maps tab.

Follow the on-screen instructions.

Purchasing Accessories

Go to

http://buy.garmin.com.

Symbol Definitions

These symbols may appear on the device or accessory labels.

Alternating current. The device is suitable for alternating current.

Direct current. The device is suitable for direct current only.

Fuse. Indicates a fuse specification or location.

WEEE disposal and recycling symbol. The WEEE symbol is

attached to the product in compliance with the EU directive

2002/96/EC on Waste Electrical and Electronic Equipment

(WEEE). It is intended to deter the improper disposal of this

product and to promote reuse and recycling.

Troubleshooting

The suction cup will not stay on my

windshield

Clean the suction cup and windshield with rubbing alcohol.

Dry with a clean, dry cloth.

Mount the suction cup (Connecting the Device to Vehicle

Power,

page

1).

My device is not acquiring satellite signals

• Verify the GPS simulator is turned off (Navigation Settings,

page 13).

• Take your device out of parking garages and away from tall

buildings and trees.

• Remain stationary for several minutes.

The device does not charge in my vehicle

• Check the fuse in the vehicle power cable.

• Verify the vehicle is turned on and is supplying power to the

power outlet.

• Verify the interior temperature of the vehicle is between 32°

and 113°F (between 0° and 45°C).

• Verify that the fuse is not broken in the vehicle power outlet.

My battery does not stay charged for very

long

• Decrease the screen brightness (Display Settings, page 14)

• Shorten the display timeout (Display Settings, page 14).

• Decrease the volume (Adjusting the Volume, page 1)

• Disable Bluetooth wireless technology (Disabling Bluetooth,

page 14)

• Put the device in sleep mode when not in use (Entering and

Exiting Sleep Mode, page 1).

• Keep your device away from extreme temperatures.

• Do not leave your device in direct sunlight.

The battery gauge does not seem accurate

Allow the device to fully discharge.

Fully charge the device without interrupting the charge cycle.

My device does not appear as a removable

drive on my computer

On most

Windows computers, the device connects using Media

Transfer Protocol (MTP). In MTP mode, the device appears as a

portable device and not as a removable drive. MTP mode is

supported by Windows 7, Windows Vista

, and

Windows XP

Service Pack 3 with Windows Media Player 10.

My device does not appear as a portable

device on my computer

On Mac

computers and some Windows computers, the device

connects using USB mass storage mode. In USB mass storage

mode, the device appears as a removable drive or volume, and

not as a portable device. Windows versions prior to Windows XP

Service Pack 3 use USB mass storage mode.

My device does not appear as either a

portable device or a removable drive or

volume on my computer

Disconnect the USB cable from your computer.

Turn off the device.

Plug the USB cable into a USB port on your computer and

into your device.

TIP:

Your device should be connected directly to a USB port

on your computer and not to a USB hub.

The device automatically turns on and goes into MTP mode or

USB mass storage mode. A picture of the device connected to a

computer appears on the device screen.

My phone will not connect to the device

• Select Settings > Bluetooth.

The Bluetooth field must be set to Enabled.

• Enable Bluetooth

wireless technology on your phone and

bring your phone within 33 ft. (10 m) of the device.

• Go to www.garmin.com/bluetooth for more help.

16 Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Fleet 670V Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Fleet 670V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info