Bedienungsanleitung Garmin GCV10 (Seite 1 von 4) (Englisch)

691444

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

GCV™ 10 Installation Instructions

To obtain the best performance and to avoid damage to your

boat, install the Garmin

GCV 10 device according to these

instructions.

Read all installation instructions before proceeding with the

installation. If you experience difficulty during the installation,

contact Garmin Product Support.

Registering Your Device

Help us better support you by completing our online registration

today.

• Go to http://my.garmin.com.

• Keep the original sales receipt, or a photocopy, in a safe

place.

Contacting Garmin Product Support

• Go to www.garmin.com/support and click Contact Support

for in-country support information.

• In the USA, call (913) 397.8200 or (800) 800.1020.

• In the UK, call 0808 2380000.

• In Europe, call +44 (0) 870.8501241.

Important Safety Information

WARNING

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

You are responsible for the safe and prudent operation of your

vessel. Sonar is a tool that will enhance your awareness of the

water beneath your boat. It does not relieve you of the

responsibility of observing the water around your boat as you

navigate.

CAUTION

Failure to install and maintain this equipment in accordance with

these instructions could result in damage or injury.

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

Installation Preparation

NOTICE

This device must be installed according to these instructions to

get the best possible performance. If you experience difficulty

with the installation, contact Garmin Product Support.

Because every boat is different, you must carefully plan the

GCV 10 sounder installation.

Select a mounting location.

Mount the sounder.

Connect the sounder to the Garmin Marine Network and to

power.

Connect the sounder to the transducer.

Tools Needed

• Drill and drill bits

• #2 Phillips screwdriver

• Cable ties (optional)

• Marine sealant (optional)

Mounting the Sounder

Mounting Location Considerations

• The sounder must be mounted in a location where it cannot

be submerged.

• The sounder must be mounted in a location with adequate

ventilation where it will not be exposed to extreme

temperatures.

• The sounder should be mounted so that the LEDs are

visible.

• The sounder should be mounted so that the power and

network cables can be easily connected.

• The sounder should be mounted so that the transducer cable

can be connected. If required, transducer extension cables

are available through your Garmin dealer.

Mounting the Device

NOTICE

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid any cracking in the gel-coat layer when the screws are

tightened.

Stainless-steel screws may bind when screwed into fiberglass

and overtightened. Garmin recommends applying an anti-seize

lubricant to the screws before installing them.

Before you mount the device, you must select a mounting

location and determine the mounting hardware needed for the

surface.

NOTE: Mounting hardware is included with the device, but it

may not be suitable for the mounting surface.

Place the device in the mounting location and mark the

location of the pilot holes.

Drill the appropriate pilot hole for one corner of the device.

Loosely fasten the device to the mounting surface with one

corner and examine the other three pilot-hole marks.

Mark new pilot-hole locations if necessary, and remove the

device from the mounting surface.

Drill the appropriate pilot holes for the other three marks.

Secure the device to the mounting location.

Connecting the Sounder

WARNING

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place will void the product warranty.

NOTICE

Do not force a cable into its port. Forcing the cable can damage

the pins. If the cable is properly aligned, the cable should

connect easily.

Before you connect the sounder to the network, power, and the

transducer, you must mount the sounder.

Route the cables using the appropriate tie wraps, fasteners,

and sealant to secure the cables along the route and through

any bulkheads or the deck (page 2).

November 2013

190-01663-02_0A Printed in Taiwan

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GCV10 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GCV10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info