Bedienungsanleitung Garmin GCV20 (Seite 2 von 2) (Englisch)

691443

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

• If your boat is not equipped with a GMS 10 network port

expander, connect the network cable directly to the

network port on your chartplotter.

Installation Diagram

You can use this diagram to identify the connection points from

your sounder to the network, power, and transducer.

Item Description

Chartplotter

GCV 20

Power Source

Transducer

Cable Routing Grommets

When routing cables through your boat, it may be necessary to

drill holes to route the cables. Cable routing grommets can be

used to cover cable installation holes. The grommets do not

create a waterproof seal. If necessary, apply a marine sealant

after installation to weatherproof around the grommet and the

cable. You can purchase grommets from your Garmin dealer or

directly from Garmin at www.garmin.com.

Blink Codes

After the sounder is installed, it turns on when the chartplotter is

turned on. The two-color (green and red) status LED on the

sounder indicates its operational status.

LED

Color

State Status

Green Slow blink The sounder is connected to a chartplotter

and is operating properly. You should see

sonar data on the chartplotter.

Red Slow blink The sounder is turned on, but is not

connected to a chartplotter, or is waiting to

connect to a chartplotter. If the sounder is

connected to the chartplotter and this code

persists, check the wiring connections.

Red/

Green

Slow blink The sounder is in test mode.

Red Rapid blink

sequence

System error. The chartplotter displays a

message indicating the type of failure. When

the error condition is fixed, the sounder must

be completely disconnected from and

reconnected to its power source to clear the

error.

Specifications

Specification Measurement

Size (W × H × D) 192 x 251 x 66 mm (7.6 x 9.9 x 2.6 in.)

Weight 845 g (1.86 lb.)

Case material Fully gasketed, polycarbonate plastic

Water rating* IEC 60529 IPX7

Temperature range From -15° to 70°C (from 5° to 158°F)

Power input From 10 to 35 Vdc

Power usage 10.5 W maximum

Fuse 4.0 A, mini 42 Vdc, fast-acting, blade-type

Compass safe distance 260 mm (10.2 in.)

Transmit power (RMS)** 500 W

Frequency CHIRP 260/455/820/1120 kHz

Maximum depth/

distance***

Garmin ClearVü

™

260 kHz: 152 m (500 ft.)

455 kHz: 91 m (300 ft.)

820 kHz: 61 m (200 ft.)

SideVü 260 kHz: 152 m (500 ft.)

455 kHz: 91 m (300 ft.)

820 kHz: 61 m (200 ft.)

1120 kHz: 38 m (125 ft.)

Data output Garmin Marine Network

*The device withstands incidental exposure to water of up to 1 m

for up to 30 min. For more information, go to www.garmin.com

/waterrating.

**Dependent upon transducer rating and depth.

***Dependent upon transducer, water salinity, bottom type, and

other water conditions.

Garmin

and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries,

registered in the USA and other countries. GCV

™

is a trademark of Garmin Ltd. or its

subsidiaries. These trademarks may not be used without the express permission of

Garmin.

support.garmin.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GCV20 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GCV20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info